Athena 2000 Series 운영 매뉴얼 - 페이지 11
{카테고리_이름} Athena 2000 Series에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Athena 2000 Series 16 페이지. Temperature/process controller
Athena 2000 Series에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지)
페이지 인쇄
Specifications
Line Voltage
Power Consumption
Setpoint
Setpoint Resolution
Indication
Accuracy
Cold Junction Compensation
Setpoint Repeatability
Thermocouple
Break Protection
Input
Sensor Lead
Resistance
Proportional Band
Offset (manual reset)
Rate (derivative)
Reset (integral)
Common Mode
Rejection
Series Mode Rejection
Ambient Temperature
Dimensions
Ordering
Codes
2
0
Output type (Plug-In) Code
Sensor Input Code
B = SPDT Relay, 7 A/5 A
0 = Thermocouple
F = 4-20 mAdc
2 = RTD
S = Pulsed 20 Vdc
T = SPST SS Relay, 1 A
L = Limit Control*
0
-
-
Control Options Code
O = Proportional
(Standard)
A = 3-mode (PID)
Alarms
B = High deviation alarm only*
C = Low deviation alarm only*
D = High and low deviation alarm*
E = Full scale process alarm*
120/240 V ± 10% to ± 15%, 50-60 Hz
Less than 5 VA
Analog-Single turn potentiometer 270° rotation
0.2% span
Temperature: Deviation meter ±50°F or ±30°C of setpoint
Load: Red LED output light
Alarm: Red LED
±0.5% of span at calibration points
Automatic, electrical
±0.3% of span
Failsafe, open sensor, output zero,
Upscale indication on meter
J,K,R,T, thermocouples, Platinum RTD DIN standard
Thermocouple, maximum lead resistance
100Ω for specified accuracy
On/off or nominal 5°F to 50°F (3°C to 30°C)
Adjustable over 100% of proportional band
0.5 to 40 sec
0.7, 1, 2 or 4 min via internal switches
Maximum error ±1°C with 240 V, 60 Hz applied
As a common mode signal between sensor input and chassis ground
Maximum error = 1°C with series mode signal of 100 mV pk-to-pk at 60 Hz
32°F to 131°F (0°C to 55°C)
Front Panel - 3.780 sq. in. (96 mm
(96 mm), Panel cutout - 3.622 sq. in. (92 mm
-
-
STANDARD RANGE CODE
Thermocouple
Code
14F
03F
04F
13F
16F
08F
01F
03C
05C
51F
02F
25F
01C
30F
Platinum RTD (3-wire, 100Ω @ 0°C)
R30
R60
R10
R06
), Depth Behind Panel - 3.780˝
2
)
2
Set Range
Type
-100 to +400°F
T
0 to +300°F
J
Special Options
0 to +400°F
J
000 = None
Consult factory for
-100 to +350°F
J
available special
100 to +600°F
J
options you may need
0 to +800°F
J
for your application.
0 to 1000°F
J
0 to +300°C
J
0 to 500°C
J
500 to +1500°F
K
0 to +2000°F
K
0 to +2500°F
K
0 to +1000°C
K
0 to 3000°F
R
0 to 300°F
0 to 600°F
0 to 1000°F
0 to 600°C
11