Electrolux EIDW 6105 서비스 데이터 시트 - 페이지 2
{카테고리_이름} Electrolux EIDW 6105에 대한 서비스 데이터 시트을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux EIDW 6105 2 페이지. Wiring diagram (all languages)
Electrolux EIDW 6105에 대해서도 마찬가지입니다: 서비스 데이터 시트 (2 페이지)
페이지 인쇄
Operation
Open door, select the cycle and options: then press
Starting a Cycle ...
the "START/CANCEL" key. The LED over the
selected cycle key will then flash. Close the door
and the cycle will begin.
Open door, select the cycle and options; then press
Delay Start ...........
the "DELAY" key. Each press of the key will increase
the delay time by 2 hours as it scrolls between the
3 options (2, 4, and 6 hours).
Selecting a new
cycle or option .... Open door, select the desired cycle and options; then
press the "START/CANCEL" key and the cycle will
begin.
Canceling a cycle . Open door, select the "START/CANCEL" key then
close the door. The unit will then drain and turn off.
Locking Controls . Open door and hold down the "air dry" key for
3 seconds. The "LOCKED" LED will illuminate and
the keys will be unresponsive. To unlock the control
hold the "AIR DRY" key down for 3 seconds -
normal function will resume.
Wire Color Codes
BK.......................... Bl a ck
Y..............................Yellow
OR.........................Orange
BLUE.......................Blue
GRN.......................Green
BRN....................... Brown
Water/Service Test
PINK........................Pink
PURP./VIO.............Purple
R...............................Red
W or WHT...............Whi t e
To enable the Relay Test mode
for checking components perform the foll o wing steps in sequence:
1. If a wash cycle is running, slowly open the door, press the "START/CANCEL" key to cancel
operation, and then close the door to allow i t to drain.
2. Re-open the door.
3. Press and hold the "Hi-Temp" key for at l e ast 3 seconds to reset the dishwasher.
EIDW6105
EIDW5905
"Favori t e" - Heater (energize only after assuring water i n sump)
"Auto"
"Auto"
- Wash Pump
"Heavy" - Water Valve
"Heavy" - Water Valve
"Normal" - Drain Motor
"Normal" - Drain Motor
"Quick" - Heater (energi z e onl y after assuri n g water in sump)
"Rinse" - Clean Light
"Saniti z e" - Lower Fan, then for 6105 units - 3 second delay then Upper Fan
"Hi-Temp" - Press repeatedly to step through diagnostic LEDS on baseboard.
EIDW6105 uni t s will simultaneously run the upper fan. Note: Do
"Air Dry" - Dispenser
Not hold key for extended time - see step 7.
"Sani t ize" - Lower Fan, then for EIDW6105 units - 3 second delay then Upper Fan
and Damper.
"Air Dry" - Dispenser
7. Press and hold the "Hi-Temp" key for at least 3 seconds to exit the test mode and reset the Dishwasher.
Display Codes (LED)
LED status indicators located in the center of the keypad
CLEAN .................... The LED labeled "CLEAN" will illuminate
when the cy cle is complete.
SANTIZED............... The LED Labeled "SANITIZE" will illuminate when
s anitization criteria has been met.
CHILD LOCK ........... T he LED labeled "LOCKED" will illuminate
when the controls are in the locked state (hold Air
Dry button for 3 seconds with door unlatched) to
enter and exit.
RINSE AGENT LOW The LED labeled "LOW RINSE" will illuminate when
rinse agent level is low.
LED status indicators located in the right of the keypad
DELAYED START .. One of 3 LEDs (labeled 2 HR, 4 HR, 6 HR)
will Illuminate to show the selected time delay
Component Error LED Indication
To gain access to the Control Housing Assembly, remove
kickplate assembly.LED indicates which component is the
source of the error.
*See Error Codes/Description on reverse side
4. Simul a taneously press "Saniti z e" and "Delay" keys.
5. Press the "Rinse" key to select Relay Test Mode.
6. Check the electrical output to any of the desired components by pressing the
assigned key as l i sted below. One press will energi z e and the next press
of the same key wil l de-ernergi z e the component. Note: that the door
must be closed to energi z e component outputs.
- Wash Pump
And Damper.
Cycle Selection Options
Wiring Diagram
*Floor LED not present