Aleo S18 LK195 빠른 참조 매뉴얼 - 페이지 7

{카테고리_이름} Aleo S18 LK195에 대한 빠른 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aleo S18 LK195 20 페이지.

페이지 인쇄

1. This Manual in Other Languages

WARNING !

Contact with live parts due to unsuitable tools

or wet conditions. Danger of electric shock!

• Only use approved, insulated tools for installation or

maintenance work on live parts.

• Work in dry conditions. Make sure that the electrical

connections on the solar module, the cables used

for installation and the tools, are dry.

7.2.1 Health and safety

CAUTION!

Risk of slipping due to wind, rain, snow or ice.

Risk of injury due to falling or colliding with

objects!

• Avoid unfavourable weather conditions, such as

strong wind or rain.

• Also avoid working on the installation site in ice and

snow.

• Use the safety equipment required or recommended

by local regulations, such as hard hats, steel-capped

shoes with rubber soles, protective goggles, gloves

or fall-protection systems.

_______________________________________________

CAUTION!

Hot module parts in strong sunlight. Risk of

burning!

• Protect yourself from burning by wearing gloves and

suitable clothing.

_______________________________________________

Mechanical Installation

8.1

Mounting orientation for modules

8.1.1 Vertical (portrait) mounting

When mounting the module vertically, make sure that the

cables are facing towards the ground and the junction box

is facing upwards.

8.1.2 Horizontal (landscape) mounting

When mounting horizontally, make sure that the exit holes

for the cables on the module or the junction box are positi-

oned on the inside of the photovoltaic generator. Avoid the

lateral outer edges of the photovoltaic generator to minimi-

se the effect of ambient conditions, such as wind or rain.

8.1.3 Inclination

Incline the surface of the modules at an angle of at least

10° horizontally, so that precipitation can drain off which

supports the modules self-cleaning.

For optimum self-cleaning, we recommend an angle of at

least 15° horizontally. In case of flat installations is advisa-

ble the employment of our unframed modules.

aleo solar GmbH | Marius-Eriksen-Straße 1 | 17291 Prenzlau | Germany | [email protected]

Quick Reference Manual Rel. 4.2, 08/2015, en-GB-DE (1)

NOTE

Avoid locations in which, over the course of the day

or year, there is systematic shadowing due to neigh-

bouring objects or buildings

Fig.1 Recommended position of the junction boxes for

horizontal mounting (facing the middle of the

generator)

8.2

Safety precautions

NOTE

• Do not drill any additional holes in aleo modules or

their frames.

8.3

Improper mounting

NOTE

• Do not attach the modules using nails. The vibration

created in the process can cause micro fissures and

loss of yield, and results in loss of warranty rights.

• Do not attach the modules by welding. The tempera-

tures created in the process can cause delaminati-

on, micro fissures and loss of yield, and results in

loss of warranty rights.

8.4

Intervals

8.4.1 Intervals between modules with standard frames

NOTE

• Leave a minimum clearance when mounting modu-

les. This prevents mechanical tension due to ther-

mal expansion.

• When mounting at intervals

Leave a clearance of 3 mm or more between the

individual module frames.

• For edge-to-edge mounting

Allow for an expansion joint of 20 mm after a

maximum of 7 m.

• The recommended maximum clearance is 30 cm,

based on the modules' standard cable length.

aleo solar recommends mounting at intervals. Also note the

information from the mounting equipment vendor. This

could specify larger intervals.

Page 7/19