Bosch Professional GWS 24-180 P 원본 사용 설명서 - 페이지 13
{카테고리_이름} Bosch Professional GWS 24-180 P에 대한 원본 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch Professional GWS 24-180 P 24 페이지.
페이지 인쇄
Rough grinding
Never use cutting discs for rough grinding.
u
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked. Flap discs have a considerably higher ser-
vice life, lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
Always use the protective guard for cutting (14) when
u
cutting bonded abrasives.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
Cutting stone
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
u
ing.
For best results when cutting stone, use a diamond cutting
disc.
When using the extraction guard for cutting with a guide
block (22), the vacuum cleaner must be approved for vacu-
uming stone dust. Suitable vacuum cleaners are available
from Bosch.
crete with a high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This is
Bosch Power Tools
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Switch on the power tool
and position it with the
front part of the guide block
on the workpiece. Move the
power tool with a moderate
feed motion that is suited to
the material being ma-
chined.
When cutting especially
hard materials such as con-
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
Working noticeably slower and with circular sparking indic-
ate that the diamond cutting disc that has become dull. You
can resharpen the disc by briefly cutting into abrasive mater-
ial (e.g. lime-sand brick).
Information on structural design
Slots in load-bearing walls are subject to DIN 1053 part 1 or
country-specific regulations. These regulations must be ob-
served under all circumstances. Seek advice from the re-
sponsible structural engineer, architect or construction su-
pervisor before starting work.
Maintenance and Service
Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
Store and handle the accessories carefully.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Dust box
To ensure optimum dust protection, we recommend clean-
ing the dust box (3) daily or at regular intervals after use.
The cleaning intervals depend on usage.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
English | 13
1 609 92A 5TG | (25.11.2020)