Electrolux AOFP061U 운영 및 유지보수 지침 매뉴얼 - 페이지 15

{카테고리_이름} Electrolux AOFP061U에 대한 운영 및 유지보수 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux AOFP061U 27 페이지. Bcf 30kg 6 gn1/1 lw (240/3/60hz), bcf 50kg 10 gn1/1 lw (240/3/60hz) / bcf 100kg 20 gn1/1 lw (240/3/60hz) / bcf 70kg 10 gn2/1 lw (240/3/60hz) / bcf 180kg 20 gn2/1 lw (240/3/60hz) / bcf 30kg 6 gn1/1 lw (208/3/60hz) / bcf 50kg 10 gn1/1 lw (208/3/60hz) / bcf
Electrolux AOFP061U에 대해서도 마찬가지입니다: 매뉴얼 (11 페이지)

페이지 인쇄

C.2 USER INSTRUCTIONS

Before using the appliance, clean the chamber with a detergent

solution, as there may still be condensation in the chamber left

over from the final testing by the manufacturers (see section D.1

for further information).

C.2.1 SWITCHING ON

Switch on the fused disconnet switch or the main circuit breaker

switch and press the I = ON button to start the appliance. The

I = ON indicator light lights up to signal that the appliance is

powered up.

C.2.2 OPERATION

C.2.2.1 Starting a "cruise chilling" cycle

To start the automatic "cruise chilling" (positive) cycle, insert

the core probe in the product and press the button

The cycle starts immediately when activated. To stop it, keep

the button

pressed for at least 3 seconds.

IMPORTANT: The "cruise chilling" cycle is not

activated when the appliance is in "programme selection"

. . . . .

status

C.2.2.2 Selecting a standard cycle

The default setting on the appliance is the SOFT chilling cycle.

Use these buttons

options:

From left to right:

• Positive "SOFT CHILLING"

• Positive "HARD CHILLING"

• Positive "COOLER" maintenance (or preservation)

• Negative "BLAST FREEZING" chilling or freezing

• Negative "FREEZER" maintenance (or preservation)

When choosing a cycle, press the

next option; the options are in a loop and so you can either scroll

forwards

or backwards

to select one of the following

button to move on to the

If you want another cycle, keep pressing the

the indicator light for the chosen cycle turns orange, and start it

by pressing the

IMPORTANT:The appliance recognizes automatically when the

food (core) probe is inserted in to the product. If the probe hasn't

been inserted in to the product, a timed cycle will start

automatically.

It is necessary to wait 2 minutes after the end of the preparation

cycle for the automatic recognition (see section below).

C.2.2.3 How to select a "turbo cooling" cycle

To select the "turbo cooling" cycle, press the key

LED

will turn orange.

To start the cycle press the key

C.2.2.4 Selecting a program:

First of all, the user has to decide what kind of cycle to launch

(SOFT, HARD, etc.) and then select the program.

Go through the following steps:

• Select the type of cycle;

• Press the program select button

light

lights up.

• press the select button

indicator light

• if the type of program is right, start it by pressing button

if not

• keep pressing the select button

button.

; the program indicator

until the chosen program

switches on.

until the chosen

button until

; the