Bosch Instructions for Use 사용 설명서 - 페이지 7

{카테고리_이름} Bosch Instructions for Use에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch Instructions for Use 10 페이지. 24" compact condensation dryer axxis - white
Bosch Instructions for Use에 대해서도 마찬가지입니다: 설치 및 운영 지침 매뉴얼 (32 페이지), 설치 및 운영 지침 매뉴얼 (32 페이지), 사용 설명서 (10 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 설치 및 사용 설명서 지침 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 작동, 관리 및 설치 지침 매뉴얼 (24 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 작동, 관리 및 설치 지침 매뉴얼 (24 페이지), 작동 및 설치 지침 (29 페이지), 사용 설명서 (10 페이지), 설치 지침 매뉴얼 (12 페이지), 사용 설명서 (8 페이지)

Bosch Instructions for Use 사용 설명서

Installation

– Scope of delivery: dryer, installation and operating instructions.
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
1.
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean, level
and firm surface.
– Do not obstruct the air inlet on the front of the dryer.
– Keep the area around the dryer clean.
– Make the dryer level using the threaded feet
and a spirit level.
– Do not remove the threaded feet under any
circumstances.
Do not set up the dryer behind a door or sliding door, as this may obstruct
the dryer door or prevent it from opening. This will prevent a potentially
fatal danger to children from locking themselves in.
Mains connection
see Safety instructions
2.
– Connect to an AC earthed socket. If in doubt have the
socket checked by a specialist.
– The mains voltage and the voltage shown on the rating
plate (
page 10) must be the same.
– The connected load and necessary fuse protection are
specified on the rating plate.

Frost protection / Transport

Frost protection - preparation
1. Empty the condensation container
2. Select any programme using the programme selector.
3. Press the
Start/Stop button
the container
4. Wait 5 minutes and then empty the condensation container again.
5. Turn the programme selector to Off.
Transport
– Prepare the dryer
see Frost protection - preparation.
– Transport the dryer in a vertical upright position.
– Following transportation, do not use the dryer for two hours.
The dryer contains residual water;
this can flow out if the dryer is tilted.

Signal

Switching on/off an acoustic signal at the end of the programme
Turn to
Press and hold Low heat
1 x to the
Off
and turn 3 x to the right
right
Low Heat
light on
an acoustic signal at the end of the programme is switched on.
Low Heat
light off
an acoustic signal at the end of the programme is switched off.
Take all accessory parts out of the
drum. The drum must be empty.
page 13.
Clean and level
Make sure that the air inlet
remains unobstructed
Do not operate the dryer if
there is a danger of frost.
page 4.
condensed water is pumped into
Press Low heat
to
switch on/off the signal

Care and cleaning

Heat exchanger
The dryer's heat exchanger is cleaned automatically during drying.
Do not pull out the condensation container during the cleaning process.
Dryer housing, control panel, air intake
Wipe with a soft, damp cloth.
Do not use harsh cleaning agents or solvents.
Remove detergent and cleaning agent residue immediately.
Filter in the condensation container
The filter is cleaned automatically when the condensation container is emptied.
However, the filter should still be cleaned regularly under running water
stubborn deposits/dirt from building up.
1. Pull out the condensation container.
2. Pull the filter out of its snap-in lock.
3. Clean the filter under running water or in the dishwasher.
4. Refit the filter.
5. Insert the condensation container so that it locks into place.
Only operate the dryer with the filter inserted.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors. Moisture sensors measure how
damp the laundry is. A thin layer of limescale may build up on the moisture sensors after
prolonged use.
1. Open the door.
2. Clean the moisture sensors using a damp sponge with a rough surface.
Do not use steel wool or abrasive materials.
Turn to
Off
8
Appliance must be switched off.
This prevents
9