Bosch 300 Series 서비스 매뉴얼 - 페이지 33

{카테고리_이름} Bosch 300 Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 300 Series 36 페이지. Built-in wall ovens
Bosch 300 Series에 대해서도 마찬가지입니다: 사용 설명서 지침 (40 페이지), 사용자 설명서 (21 페이지), 설치 매뉴얼 (6 페이지), 설치 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 사용 설명서 (50 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 설치 매뉴얼 (28 페이지), 빠른 시작 매뉴얼 (7 페이지), 사용 및 관리 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

Bosch 300 Series 서비스 매뉴얼
7.3

Testing

Test with wire harness off at pin header or with circuits open.
Plug
Pins
Operates
X102
4, 5
Upper oven
and
double line break
X103
2, 4
relay coil
X105
7
Upper door latch
motor
X105
6
Upper oven
convection motor
X105
1
Rotisserie motor
X106
1 (common),
Upper oven door
6, 7
latch
X107
4, 5
Upper oven
sensor
X107
1, 2, 3
Cooling fan
motors
X207
1,4,5
X202
1, 2
Lower oven
and
double line break
X203
3, 5
relay coil
X205
6
Lower door latch
motor
X205
1
Lower oven
convection motor
Explanation
No fail code. If double line break relay
does not close, L2 (120 volts) will not
reach upper oven bake, broil,
convection elements.
Will accept all modes except self-
clean. When oven set to self-clean,
display will be on constantly, doors
will not lock and self-clean will not
start. E106 will appear.
No fail code. Lower oven convection
motor will not work.
No failure code. Rotisserie will not
rotate.
If latch position is not detected during
normal operation, E124/126 will be
displayed.
Controls function normal. When
sensor opens, E101 code will appear.
If sensor shorts, E104 will appear.
Cooling fan is on constantly.
Will accept modes. In ~45 seconds,
E118 will appear in upper oven
display or E218 will appear in lower
oven display when hall sensor does
not detect fan rotation.
No fail code. If double line break relay
does not close, L2 (120 volts) will not
reach lower oven bake, broil,
convection elements.
Will accept all modes except self-
clean. When oven set to self-clean,
display will be on constantly, doors
will not lock and self-clean will not
start. E206 will appear.
No fail code. Lower oven convection
motor will not work. Relay will snap
closed.
Plug
Pins
Operates
X206
1 (common),
Lower oven door
6, 7
latch
X207
3, 6
Lower oven
sensor
X2
Sends display
signal to display
X2
Sends
communication
signals to display
Table 9 Troubleshooting
8

WIRING DIAGRAMS AND SCHEMATICS

The wire color key (Table 10) and element strip diagrams (Figures 23-
24) are shown below. For schematics, please refer to the Built-in
Oven Service Guide (Wiring Diagram) which can be found on
QuickFinder or in the upper oven plenum, near the control module.
8.1

Wire Color Key

BK
Black
BN
GN
Green
OR
VT
Violet
WH
BN/WH
Brown/White
BU/WH
VT/WH
Violet/White
YE/BK
Table 10 Wire color key
Service Manual for Bosch Built-in Wall Ovens
Explanation
If latch position is not detected during
normal operation, E224/226 will be
displayed.
Control functions normal. When
sensor opens, E201 code will appear.
If sensor shorts, E204 will appear.
Cooling fan is on constantly.
Glass control panel is completely
dead. 3-position connector
(ground/voltage/data line) should
measure 9.6 VDC.
If no communication between
electronic modules, E005 will display.
Connector positions 1-2 should
measure ~5 VDC.
Brown
BU
Blue
Orange
RD
Red
White
YE
Yellow
Blue/White
OR/BK
Orange/Black
Yellow/Black
Page 33 of 36