Bosch Programme Table 사용 설명서 - 페이지 2

{카테고리_이름} Bosch Programme Table에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch Programme Table 8 페이지. Front-loading washing machine
Bosch Programme Table에 대해서도 마찬가지입니다: 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 설치 및 운영 지침 매뉴얼 (32 페이지), 설치 및 운영 지침 매뉴얼 (32 페이지), 사용 설명서 (10 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 설치 및 사용 설명서 지침 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (10 페이지), 작동, 관리 및 설치 지침 매뉴얼 (24 페이지), 사용 설명서 (8 페이지), 사용 설명서 지침 (10 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지), 사용 설명서 (8 페이지), 작동, 관리 및 설치 지침 매뉴얼 (24 페이지), 작동 및 설치 지침 (29 페이지), 사용 설명서 (8 페이지), 사용 설명서 (10 페이지), 사용 설명서 (10 페이지), 사용 설명서 (8 페이지)

Bosch Programme Table 사용 설명서
Safety instructions
– Read and follow the operating and installation instructions and all other information enclosed with the washing
machine.
– Retain documents for subsequent use.
Risk of electric shock
– Never pull out the mains plug by tugging the power cord!
– Insert/pull out the mains plug with dry hands only.
Danger to life
On redundant appliances:
– Pull out the mains plug!
– Sever the power cord and discard together with the plug.
Care
– Destroy the lock on the washing-machine door. This will prevent children from
locking themselves in and suffocating.
Risk of suffocation
– Keep packaging, plastic film and packaging parts out of the reach of children.
Risk of poisioning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Caused by detergents containing solvents, e.g. stain remover/items of washing
pretreated with solvent naphtha may result in an explosion after being loaded into
the washing machine.
Before hand thoroughly rinse items of washing by hand.
1. Pull out, depress insert, take out drawer all the way.
Risk of injury
– Washing machine door may become very hot.
2. Take out insert: using your finger, press insert upwards.
– Caution when draining hot detergent solution.
3. Clean detergent dispenser and insert with water and a brush and dry.
– Do not climb on the washing machine.
4. Attach insert and lock into position (push cylinder onto guide pin).
– Do not lean on the open washing machine door.
5. Slide in the detergent dispenser.
– Do not reach into the drum in case it is still rotating.
Consumption values
Additonal
Programme
Programme
Load
Current**
Water**
function
duration**
Cottons 30 °C*
+
7 kg
0.55 kWh
75 l
2:12 h
Eco
Cottons 40 °C*
+
7 kg
0.85 kWh
75 l
2:12 h
Eco
Cottons 60 °C*
+
7 kg
1.50 kWh
75 l
2:12 h
Eco
Cottons 90 °C
+
7 kg
2.51 kWh
90 l
2:12 h
Eco
Information on the display panel
Easy-Care 40 °C*
+
3.5 kg
0.55 kWh
55 l
1:12 h
Eco
Delicates/Silk 30 °C
-
2 kg
0.20 kWh
39 l
0:40 h
:
Wool 30 °C
-
2 kg
0.20 kWh
40 l
0:36 h
:
,
* Programme setting for test according to currently valid European standard 60456.
:
Information about comparability tests:
+
To test the test programmes, wash indicated load, with
Eco
additional function and at maximum selectable spin speed.
:
:
Additonal
Annual energy
Annual water
Programme
Load
function
consumption
consumption
Other displays
Cottons Eco
+
7/3.5 kg
218 kWh
10560 l
Eco
**
** Programme setting for testing and energy labelling according to directive 2010/30/EU with cold water (15 °C).
***The values may deviate from the stated values depending on water pressure and hardness, room temperature, type and
amount of laundry, detergents used, fluctuations in the mains voltage and selected additional functions.
7
8
Insert for liquid detergent
Maintenance
depending on model
Detergent-solution pump
Position insert for dosing liquid detergent:
– Completely remove detergent drawer.
Page 10
Set programme selector to Off , pull out the mains plug.
– Push insert forwards.
1. Take the drainage hose out of the holder.
Do not use insert (push upwards):
Remove sealing cap, allow detergent solution to flow out.
– For gel-like detergents and washing powders,
Put the closing cap back on the hose.
– For programmes with
Prewash or
(Ready in) option.
2. Carefully unscrew the pump cover (residual water).
– Risk of electric shock! Pull out the mains plug!
– Risk of explosion! No solvents!
3. Clean the interior, pump cover thread and pump housing
(fan impeller in the detergent-solution pump must rotate).
Machine housing, control panel
– Remove detergent residue immediately.
4. Reinsert and screw on pump cover. Handle is upright. Insert the drain hose into the holder.
– Wipe with a soft, damp cloth.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the
Drainage hose on the siphon
Set programme selector to Off , pull out the mains plug.
1. Loosen hose clip, carefully remove drainage hose (residual water).
Leave detergent drawer open so that residual water can evaporate.
2. Clean drainage hose and siphon spigot.
3. Re-attach drainage hose and secure connection point with hose clip.
Drum
Filter in the water inlet hose
Leave washing machine door open so that the drum can dry out.
Risk of electric shock!
Use chlorine-free cleaning agent, not steel wool.
Do not immerse Aqua-Stop safety device in water (contains electric valve).
Descaling
No washing in the machine!
Release water pressure in the supply hose:
Not required if detergent dosed correctly. However, if this does occur, follow the instructions of the descaling agent
1. Turn off the tap!
manufacturer. Suitable descalers can be purchased on our website or from customer service.
2. Select any programme (except
3. Select
Start/Pause. Leave programme for approx. 40 seconds.
4. Turn the programme selector to Off . Pull out the mains plug.
depending on model
Clean the filter:
Close the washing machine door properly; washing may be caught.
5. Disconnect the hose from the water tap.
Turn on tap fully, supply hose kinked/jammed; clean filter
Page 10, water pressure too low.
Clean filter with small brush.
Drain pump blocked; clean drain pump.
Page 10
Drainage hose/outlet pipe blocked; clean drainage hose on the siphon.
Page 10
and/or for standard and Aqua-Secure models:
remove hose from the rear of the appliance,
Water in the base pan, appliance leaking. Call customer service!
take out filter with pliers and clean.
,
,
Motor fault. Call customer service.
Installation Instructions
Switch off appliance, wait 5 seconds and switch on again. If the display is indicated again,
6. Connect the hose and check for leaks.
call customer service.
Installation Instructions
9
Risk of scalding!
What to do if ...
– Allow detergent solution to cool down!
– Turn off the tap!
Water is running out.
– Correctly attach/replace drainage hose.
– Tighten screw-fitting on the supply hose.
Water not flowing in.
Start/Pause not selected?
Detergent not washed in.
– Tap not open?
– Filter blocked? Clean the filter.
– Supply hose kinked or jammed?
Washing-machine door cannot
– Safety function active. Stop programme?
be opened.
(rinse stop = without final spin) selected?
– Can be opened via emergency release only?
Programme does not start.
Start/Pause or
– Door closed?
Detergent solution is not drained. –
(rinse stop = without final spin) selected?
– Clean the drain pump.
– Clean outlet pipe and/or drainage hose.
Water not visible in the drum.
– Not a fault – water below the visible area.
Spin result not satisfactory,
– Not a fault – unbalanced load detection system has stopped the spin cycle,
washing wet/too damp.
washing unevenly distributed.
Distribute small and large items of washing in the drum.
Reduced Ironing selected?
Drain programme.
– Too low speed selected?
The programme duration
– Not a fault – the programme sequence is optimised for the particular wash process.
changes during the wash cycle.
This may result in changes to the programme duration in the display field.
Spin cycle actuated several
– Not a fault – unbalanced load detection system adjusts imbalance.
times.
Residual water in the dispenser
– Not a fault – effect of the care product not impaired.
for care product .
– If required, clean insert.
Odour formation in the washing
– Run
Cottons 90 °C programme without washing. Use standard detergent.
machine.
Foam is coming out of the
– Too much detergent used?
detergent drawer.
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into dispenser II
(not for outdoor, sports and down-filled textiles!).
– Reduce detergent dosage for the next wash cycle.
Spin/
Drain).
Loud noise formation, vibrations
– Appliance feet fixed? Secure appliance feet.
and "Wandering" during spin
– Transportation protection devices removed?
cycle.
Remove transportation protection devices.
Noises during spin and drain
– Clean the drain pump.
cycles.
Display panel/indicator lights do
– Power failure?
not function while the appliance
– Fuse tripped? Switch on/replace fuse.
is running.
– If the fault occurs repeatedly, call customer service.
The programme takes longer
– Not a fault – unbalanced load detection system adjusts imbalance by repeatedly
than usual.
distributing the washing.
– Not a fault – foam detection system active – a rinse cycle is switched on.
Detergent residue on the
– Occasionally phosphate-free detergents contain water-insoluble residue.
washing.
Rinse or brush the laundry after washing.
– Select
In the pause status
Start/
– Water level too high. Washing cannot be reloaded.
Pause flashes very quickly and a
Immediately close washing machine door.
signal sounds.
– Select
Start/Pause to continue the programme.
If a fault cannot be rectified (switching the machine on and off) or a repair is required:
– Set programme selector to Off and pull out the mains plug.
– Turn off the tap and call customer service.
Installation Instructions
10
Page 10
Page 4
Page 3, 4
Page 6
(Ready in) time selected?
Page 3, 4
Page 10
Page 5
Page 5
Page 9
Installation Instructions
Installation Instructions
Page 10
Washing machine
en Operating instructions
11