Andis AG2 사용 및 관리 지침 매뉴얼 - 페이지 2

{카테고리_이름} Andis AG2에 대한 사용 및 관리 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andis AG2 12 페이지. Andis company model ag2 hair trimmer - use and care guide
Andis AG2에 대해서도 마찬가지입니다: 사양 (2 페이지), 사용 및 관리 (2 페이지)

페이지 인쇄

E N G L I S H

Please read the following instructions before using your new Andis

clipper. Give it the care that a fine precision built instrument deserves

and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should

always be followed, including the following: Read all

instructions before using the Andis clipper.

DANGER:

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.

Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be

pulled into a tub or sink. Do not place in or drop into

water or other liquid.

4. Always unplug this appliance from the electrical outlet

immediately after using.

5. Unplug this appliance before cleaning, removing or

assembling parts.

WARNING:

To reduce the risk of burns, fire

electric shock, or injury to persons:

1. An appliance should never be left unattended when

plugged in.

2. Close supervision is necessary when this appliance is used

by, on or near children or individuals with certain disabilities.

3. Use this appliance only for its intended use as described

in this manual. Do not use attachments not recommended

by Andis.

4. Never operate this appliance if it has a damaged cord or

plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water. Return the appliance

to an Andis Authorized Service Station for examination

and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray)

products are being used or where oxygen is being

administered.

8. Do not use this appliance with a damaged or broken

blade or comb, as injury to the skin may occur.

9. To disconnect turn control to OFF then remove plug from

outlet.

10. WARNING: During use, do not place or leave appliance

where it may be (1) damaged by an animal or (2) exposed

to the weather.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

To reduce the risk of electric shock, this appliance has a polarized plug (one

blade is wider than the other). This plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the proper outlet. Do not

change the plug in any way.

OPERATING INSTRUCTIONS

Before starting clipper, remove blade guard (some models may not have a blade

guard). Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical

current or as noted on the unit. To start clipper, move switch button to ON

position. To stop clipper, move switch button back to original position. After

using your clipper, rewrap cord and store in a safe place.

2-SPEED UNIT OPERATION

Your clipper comes with normal and high speed operation. Use the normal

setting (Setting #1) for most cutting needs. Use the high speed setting

(Setting #2) for cutting through heavy coats.

REMOVING BLADE SET

To remove blade set, first make sure your clipper is switched OFF and UNPLUGGED.

Push down on blade, then gently pull the blade forward (Figure A), and slide it

off the blade hinge. If your blade hinge should snap closed and is flush with the

clipper, use a small standard screwdriver to pry the tongue of the hinge out

(Figure B). NOTE: Hair may accumulate in the front cavity of the housing under