Andis AGP 사용 및 관리 지침 매뉴얼 - 페이지 3
{카테고리_이름} Andis AGP에 대한 사용 및 관리 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andis AGP 12 페이지. Andis company model agp hair clipper - use and care guide
Andis AGP에 대해서도 마찬가지입니다: 사양 (2 페이지), 사용 및 관리 (2 페이지)
페이지 인쇄
the blade. If this happens, you can clean out the hair by brushing out the cavity
with a small brush or an old toothbrush while the blade is off the clipper.
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of
the clipper (Figure C) and with the clipper turned ON, push the blade towards
the clipper to lock into position.
USER MAINTENANCE
The internal mechanism of your motor clipper has been permanently lubricated
by the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis Company,
or an Andis Authorized Service Station. To find an Andis Authorized Service
Station near you log on to www.andis.com or contact our customer service
department: 1-800-558-9441 (U.S.) or 1-800-335-4093 (Canada).
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat
often, especially on close cutting blades. If blades are too hot, dip the blades
only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis
Clipper Oil. If you have a detachable blade unit, you can change your blade in
order to maintain a comfortable temperature; using multiple blades of the same
size is popular among groomers.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades
leave streaks or slow down, it's a sure sign blades need oil. Place a few drops of
Andis Clipper Oil on the front and side of the cutter blades (Figure D). Wipe
excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil
for good lubrication, but are an excellent clipper blade coolant. Always replace
broken or nicked blades to prevent injury. You can clean the excess hair from
your blades by using a small brush or worn out tooth brush. To clean the blades
we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil,
while the clipper is running. Any excess hair and dirt that has accumulated
between the blades should come out. After cleaning, turn your clipper OFF and
dry blades with a dry cloth and start clipping again.
If upon cleaning your blades you find that the blades will still not cut, there may
be a few fine pieces of hair trapped between the upper and lower blade. If this
happens, you will need to snap the blade off the clipper. Proceed to slide the
upper blade to one side, without loosening the tension spring or moving the
upper blade completely out from under the tension spring (See Figure E for
position of blade). Wipe the surface between the blades clean with a dry cloth,
then place a drop of clipper oil where the upper and lower blades meet and also
4
FIGURE A
OIL
OIL
OIL
FIGURE D
BLADE
DRIVE
MOUNTING
SCREWS
FIGURE G
INCORRECT
POSITION
OF DRIVE
BEARING
INSERT BEVEL SIDE FIRST
FIGURE J
FIGURE B
FIGURE C
FIGURE E
FIGURE F
CORRECT
POSITION
OF
DRIVE
BEARING
FIGURE H
FIGURE I
TOP OF CLIPPER
CARBON BRUSH CANAL
CARBON BRUSH
SPRING
BEVEL
FIGURE K
CAP
5