Andis Detachable Plus AG 사용자 설명서

{카테고리_이름} Andis Detachable Plus AG에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Andis Detachable Plus AG 2 페이지. Andis model ag detachable blades are compatible with oster model a5
Andis Detachable Plus AG에 대해서도 마찬가지입니다: 사용 및 관리 (2 페이지)

페이지 인쇄

clockwise only until you feel the brush cap stop. If the

brush cap is tightened too tightly, it will force the

brush spring past the carbon brush and will cause

damage to the commutator.

CHANGING THE BLADE ASSEMBLY

If your clipper blades no longer cut properly (be sure

to try more than one blade, since blade currently

being used may be dull), it could be that your blade

drive assembly needs replacement.

To change the blade drive assembly:

Unplug your clipper.

Remove blade set.

HINGE

SCREWS

Remove four housing

screws with philips

screwdriver.

Turn clipper over and

remove cover.

DIAGRAM H

Before attempting to

remove the blade

drive assembly, you

must remove the

blade hinge first.

Remove the

two blade hinge

screws

(Diagram H). When

DIAGRAM I

removing the blade

hinge, you will notice

a small spring set in

between the hinge

BLADE

and the lower hous-

DRIVE

MOUNTING

ing (Diagram I). Make

SCREWS

sure that this part

does not get lost

when replacing the

DIAGRAM J

blade drive assembly.

Remove blade drive

mounting screws

(Diagram J).

NOTE: Before remov-

ing blade drive assem-

bly, note the way it is

positioned (this will

help you in reassem-

bly). Remove blade

drive assembly

(Diagram K).

DIAGRAM K

Drive bearing should be

CORRECT

at its lowest position, if

POSITION

not, move it with your

DRIVE

BEARING

finger to lowest position

(Diagrams L and M).

Align screw holes of

new blade drive assem-

bly and press down

DIAGRAM L

level at the screw holes

INCORRECT

(Diagram N).

POSITION

OF DRIVE

BEARING

10. Reassemble blade

drive mounting screws

(Diagram J).

11. Be sure the hinge

spring is in its place

DIAGRAM M

before attempting to

replace the blade hinge

and screws (Diagram

O). When replacing the

hinge screws, place

screw in the screw hole

and slowly turn count-

SPRING

er-clockwise until you

feel the screw drop into

DIAGRAM N

place. This assures the

screw is properly

aligned within the hole

threads. Turn screw

clockwise to tighten,

just until snug. DO NOT

OVER-TIGHTEN.

12. Replace cover and turn

DIAGRAM O

clipper over.

13. Replace housing screws. (Short screws in back

by cord—long screws in front by blade).

Please see enclosed slip sheet

for all Andis Authorized repair stations

FACTORY REPAIR SERVICE

When the blades of your Andis Clipper become dull

after repeated use, it is advised to send your blades

to an Andis Authorized Service Station mentioned

below for resharpening. If you wish your clipper to be

serviced as well, they should be carefully packed and

mailed either Parcel Post Insured, or U.P.S.

LIMITED WARRANTY

This Andis product is warranted against defective material or workmanship

for one year from the date of purchase. All implied warranties arising and by

virtue of State law shall also be limited to one year. Any Andis product deter-

mined to be defective in material or workmanship during the warranty period

will be repaired or replaced without cost to the consumer for parts and labor.

The defective product must be returned with proof of purchase and $6.50 to

cover cost of handling, to any Authorized Andis Repair Station or to: Andis,

1800 Renaissance Blvd., P.O. Box 085005, Racine WI 53408-5005 USA or IN

CANADA to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse,

Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the

nature of the problem. Due to foreign matter sometimes found in hair, clipper

blades or resharpening of blades are not subject to the one year warranty. The

blade set has a 10 Day Limited Warranty. If the blade set fails to cut, it will be

resharpened free of charge if returned within 10 days of purchase. Send your

blade set postage prepaid with the original purchase receipt to: ANDIS COM-

PANY, ATTENTION: Service Department, 1800 Renaissance Blvd, Sturtevant,

Wisconsin 53177 (U.S. & Canada only). Andis will not be liable under this war-

ranty for any defect, failure or malfunction of any of its products caused by

normal wear, abuse, misuse, unauthorized adjustments or disassembling.

Andis will not be liable for any consequential damages resulting from any

defect in material or workmanship of any of its products. Some States do not

allow limitations on how long an implied warranty lasts or exclusion or limi-

tation of incidental or consequential damages, so the above limitations or

exclusions may not apply to you. The Warranty gives you specific legal rights,

and you may also have other rights which may vary from State to State.

Date Purchased ___________________________ Model ____________

KEEP THIS FOR YOUR RECORDS

Form # 27074 Rev. N

Printed in U.S.A.

Detachable Plus

MODEL AG

Clipper

Andis Model AG

Detachable Blades

are compatible with

Oster Model A5

Congratulations –

you just went First Class when you bought

this Andis Clipper. Careful workmanship and

quality design have been the hallmarks of

Andis products since 1922.