Andis SLII 사용 및 관리 지침 매뉴얼 - 페이지 4

{카테고리_이름} Andis SLII에 대한 사용 및 관리 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andis SLII 14 페이지. Andis company hair trimmer - use and care guide
Andis SLII에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (2 페이지), 사용 및 관리 (2 페이지)

페이지 인쇄

carE aNd SErvIcING of Your aNdIS trImmEr BLadES

Blades should be oiled before, during, and after each use. If your trimmer

blades leave streaks or slows down, it's a sure sign blades need oil. The

trimmer should be held in the position shown in Figure D to prevent oil

from getting into motor. Place a few drops of Andis Clipper Oil on the

front and side of the cutter blades (Figure E). Wipe excess oil off blades

with a soft dry cloth. Spray lubricants contain insufficient oil for good

lubrication, but are an excellent blade coolant. Always replace broken or

nicked blades to prevent injury. You can clean the excess hair from your

blades by using a small brush or worn out tooth brush. To clean the

blades we suggest to immerse the blades only into a shallow pan of

Andis Clipper Oil, while the trimmer is running. Any excess hair and dirt

that has accumulated between the blades should come out. After

cleaning, turn your trimmer off and dry blades with a dry cloth and start

clipping again.

rEpLacEmENt (rEmovaL) of BLadE SEt for

aE trImmErS

NotE: If you are familiar with replacing and adjusting T-Edjer trimmer

blades, please read the following blade replacement instructions. If you

are not familiar with this procedure, please return trimmer to your supplier

or an Andis Authorized Service Station for blade replacement and

adjustment.

To remove blade set from your trimmer, unplug your trimmer from the

electrical outlet. Turn the trimmer upside down so the teeth of blades are

facing down. You may wish to set the trimmer on a flat surface while

performing these operations. Using a philips type screwdriver, unscrew

the two blade screws (Figure F). Remove blade set from trimmer. To install

your new trimmer blade set, align hole in upper blade (smaller of the two

blades) and center over nylon roller (ball) of the trimmer's tension spring

(Figure G). Align screw holes of lower blade (larger of the two blades) to

armature screw holes. While holding blade in place, replace blade screws;

do not tighten down completely. Turn trimmer over and align the blade

set parallel to the trimmer's upper housing.

ImportaNt: Check blade alignment, making sure the teeth of the upper

blade rest slightly below the upper edge of teeth on lower blade. Failure

to check the position of blade may cause cutting or scratching of your

client's skin when trimming. Tighten down blade screws firmly. If after

turning on the trimmer you notice the hair guard (Figure H) is hitting the

upper blade, loosen (with standard screwdriver) hair guard screws slightly

and adjust hair guard away from the upper blade approximately 1/32".

Tighten down hair guard screws.

rEpLacEmENt (rEmovaL) of BLadE SEt for

SLII, SL3 trImmErS

Your Andis SLII and SL3 trimmers have a preset tension assembly on the

blade set. To remove blade set from your trimmer, unplug trimmer from

electrical outlet. Turn the trimmer upside down so teeth of blades are

facing down. You may wish to set the trimmer on a flat surface while

performing these operations. Using a philips type screwdriver, unscrew

the two blade screws (Figure F). Remove blade set from trimmer. Install

new blade set, making sure the blade yoke cradles the armature pin on

trimmer (Figure I). There is no need to adjust blade tension before use, as

tension has been preset at the factory. Align screw holes of blade set to

screw inserts on trimmer housing. Replace the screws. Before tightening

down blade screws, check alignment of blade set to housing, making sure

that they are parallel. Tighten down screws.

poWEr adJuStmENt for modELS SLII aNd SL3

Your Andis trimmer has been adjusted to line voltage at the factory.

However, because of voltage variations it may be necessary to adjust the

power setting for your area. If the power adjustment is off, you will usually

notice a "clatter", when the trimmer is on or introduced into the hair. (It is

normal for your trimmer to "clatter" for an instant when initially turned on).

to adJuSt Your trImmEr:

1. Oil the blades (Figure E).

2. The power screw is located in the lower part of the housing opposite

the switch (Figure J).

3. Turn your trimmer ON.

4. Using a standard screw driver that fits the slot, turn the powescrew

counter clockwise until the trimmer clatters continuously. Then turn the

screw clockwise carefully until the clatter ceases.

5. Your trimmer is now adjusted to its optimum power setting.