Bosch 4 V-LI 원본 사용 설명서 - 페이지 9

{카테고리_이름} Bosch 4 V-LI에 대한 원본 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 4 V-LI 15 페이지. Professional
Bosch 4 V-LI에 대해서도 마찬가지입니다: 사용 설명서 (31 페이지), 원본 사용 설명서 (7 페이지), 원본 사용 설명서 (10 페이지), 원본 사용 설명서 (7 페이지), 원본 사용 설명서 (48 페이지), 원본 사용 설명서 (14 페이지)

페이지 인쇄

OBJ_BUCH-1257-001.book Page 21 Thursday, July 15, 2010 9:04 AM

The vibration emission level given in this infor-

mation sheet has been measured in accordance

with a standardised test given in EN 60745 and

may be used to compare one tool with another.

It may be used for a preliminary assessment of

exposure.

The declared vibration emission level repre-

sents the main applications of the tool. However

if the tool is used for different applications, with

different accessories or poorly maintained, the

vibration emission may differ. This may signifi-

cantly increase the exposure level over the total

working period.

An estimation of the level of exposure to vibra-

tion should also take into account the times

when the tool is switched off or when it is run-

ning but not actually doing the job. This may sig-

nificantly reduce the exposure level over the to-

tal working period.

Identify additional safety measures to protect

the operator from the effects of vibration such

as: maintain the tool and the accessories, keep

the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that

the product described under "Technical Data" is

in conformity with the following standards or

standardization documents: EN 60745 accord-

ing to the provisions of the directives

2004/108/EC, 2006/42/EC.

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider

Dr. Eckerhard Strötgen

Senior Vice President

Head of Product

Engineering

Certification

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

18.06.2010

Bosch Power Tools

Assembly

Before any work on the machine itself (e. g.

maintenance, tool change, etc.) as well as

during transport and storage, remove the

battery from the power tool. There is danger

of injury when unintentionally actuating the

On/Off switch.

Battery Charging

Use only the battery chargers listed on the

accessories page. Only these battery charg-

ers are matched to the lithium ion battery of

your power tool.

Note: The battery is supplied partially charged.

To ensure full capacity of the battery, complete-

ly charge the battery in the battery charger be-

fore using your power tool for the first time.

The lithium ion battery can be charged at any

time without reducing its service life. Interrupt-

ing the charging procedure does not damage the

battery.

The lithium ion battery is protected against

deep discharging by the "Electronic Cell Protec-

tion (ECP)". When the battery is empty, the ma-

chine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Do not continue to press the

WARNING

On/Off switch after the ma-

chine has been automatically switched off. The

battery can be damaged.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A long

battery service life is achieved in this manner.

Observe the notes for disposal.

Removing the Battery

The battery 3 is equipped with two locking lev-

els that should prevent the battery from falling

out when pushing the battery unlocking button

4 unintentionally. As long as the battery is in-

serted in the power tool, it is held in position by

means of a spring.

To remove the battery 3, press the battery un-

locking button 4 and pull the battery toward the

rear out of the power tool. Do not exert any

force when doing this.

1 609 929 W85 | (15.7.10)

English | 21