Bosch 8-LI Professional 원본 사용 설명서 - 페이지 9

{카테고리_이름} Bosch 8-LI Professional에 대한 원본 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 8-LI Professional 10 페이지. Jigsaw and sabre saw
Bosch 8-LI Professional에 대해서도 마찬가지입니다: 원본 사용 설명서 (13 페이지), 원본 사용 설명서 (39 페이지), 원본 사용 설명서 (13 페이지), 원본 사용 설명서 (8 페이지)

페이지 인쇄

1. Maintenance and Service

OBJ_BUCH-1531-001.book Page 14 Friday, September 2, 2011 9:57 AM

14 | English

For the working of paint/enamel

coats or primers and fillers

For sanding off paint

For sanding primer

For final sanding of primers before

coating

For reworking or polishing, especially of metal and stone, use

fleece/polishing cloth pad.

Depending on the desired surface quality of the workpiece,

different fleece types or polishing cloth pads are to be used.

Replacing the Sanding Plate

The supplied sanding plate 6 consists of two parts: base and

replaceable front triangle. The front triangle is fitted with Vel-

cro backing and can be replaced. To remove the sanding plate

front triangle, grasp it at one of the tips and pull it off.

Operation

Starting Operation

Inserting the Battery

Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Switching On and Off

To start the machine, push the On/Off switch 2 towards the

front to "I".

To switch off the machine, push the On/Off switch 2 towards

the rear to "0".

Battery Charge-control Indicator/Overload Indicator

The battery charge-control indicator/overload indicator 1 in-

dicates the charge condition of the battery and overload con-

ditions when the machine is switched on.

LED

Capacity

≥ 30%

Continuous lighting, green

Continuous lighting, red

< 30%

During operation with increased load, the battery charge-con-

trol indicator/overload indicator 1 flashes green. This indi-

cates a higher operation level.

When using the machine as intended for, it cannot be subject

to overload. In case of excessive loading, the battery charge-

control indicator/overload indicator 1 flashes red for a dura-

tion of up to approx. 2 seconds. In case of prolonged over-

loading, the motor gradually stops within one second and the

battery charge-control indicator/overload indictor 1 flashes

red for approx. 5 seconds.

2 609 005 580 | (2.9.11)

When exceeding the allowable battery temperature of 70 °C,

Grain size

the electronics immediately switch the machine off until it is

40—180

in the optimal operating-temperature range again. The bat-

tery charge-control indicator/overload indicator 1 flashes

red for approx. 5 seconds.

Note: If the machine should automatically switch off because

coarse

of a discharged or overheated battery, make sure to set the

medium 80, 120

machine's On/Off switch 2 to off. Charge the battery and al-

low it to cool down before restarting the machine. Otherwise

fine

180

the battery can become damaged.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging

by the "Electronic Cell Protection (ECP)". When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates and the battery

charge-control indicator/overload indicator 1 flashes red for

approx. 5 seconds.

Working Advice

Wait until the machine has come to a standstill before

placing it down.

The removal capacity during sanding is mainly determined by

the selection of the sanding sheet.

Only flawless sanding sheets achieve good sanding capacity

and extend the service life of the machine.

Pay attention to apply uniform sanding pressure; this increas-

es the working life of the sanding sheets.

For precise on-the-spot sanding of edges, corners and hard to

reach areas, it is also possible to work only with the tip or an

edge of the sanding plate.

A sanding sheet that has been used for metal should not be

used for other materials.

Use only original Bosch sanding accessories.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

For safe and proper working, always keep the machine

and ventilation slots clean.

When the battery is no longer operative, please refer to an au-

thorised after-sales service agent for Bosch power tools.

If the machine should fail despite the care taken in manufac-

turing and testing procedures, repair should be carried out by

an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

Bosch Power Tools