Dremel DIGILAB 3D40 빠른 시작 매뉴얼

{카테고리_이름} Dremel DIGILAB 3D40에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dremel DIGILAB 3D40 2 페이지.

페이지 인쇄
Dremel DIGILAB 3D40 빠른 시작 매뉴얼
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
WARNING
WARNING
DREMEL 3D40 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
UNBOXING
1
1
3
3
5
5
KNOW YOUR DREMEL 3D40
1
1
2
2
1
2
12
12
12
11
11
11
8
8
7
7
10
9
6
10
10
9
6
9
6
22
23
24
22 23 24
22 23 24
FILAMENT
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
WARNING
WARNING
INSTRUCTIONS WHEN USING THE DREMEL 3D40.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position.
2. Twist spool door counter-clockwise and remove.
3. Place filament spool onto spool holder with spool being fed from the bottom
towards the back of the Dremel 3D40.
4. Thread filament through filament guide tube and replace
spool door.
5. Insert the filament coming from the filament guide tube into the extruder intake.
6. Plug power cord into outlet and turn on power switch.
7. Tap "Filament" on your Dremel 3D40's touch screen and wait for extruder to
heat.
8. When Feed Filament screen appears, tap "Next" and thread filament into
extruder intake until extruder feeds through on
its own.
9. When new filament appears from extruder tip, tap "Done" to complete filament
load process.
English
3D40 Quick Start Guide
2
2
4
4
14
14
15
15
16
16
14
15
16
13
13
13
3
3
3
4
4
4
19
19
19
5
5
5
20
20
20
25
25
26
26
25
26
FIG. 1
3
3
7
7
9
9
SIDE 1
KIT CONTENTS*
Dremel 3D40
Instruction Manual
1 Filament Spool
Power Cable
Build Tape
Object Removal Tool
TIP:
Save your Dremel 3D40 packaging for future transportation
and storage.
1.
Lid
17 18
17 18
2.
Extruder
17
18
3.
Z-Axis Guide Rail
4.
Door
5.
Gripping Handles
6.
USB A Port
7.
Leveling Knobs
8.
Build Platform Clip
9.
Touch Screen
10. Build Platform
11.
Filament Spool Holder
12. Filament Spool
13. Y-Axis Guide Rail
14. Stepper motor
15. Filament Guide Tube
21
21
21
16. Extruder Intake
17. Extruder Fan
18. Ribbon Cable
19. X-Axis Guide Rail
20. Leveling Sensor
21. Extruder Tip
22. Power Switch
23. USB B Port
24. Ethernet Port
25. Nameplate
26. Power Input
Spool
Holder
Open
Filament
Filament
Guide Tube
Close
!
FILAMENT
LEVEL
!
PRESS DONE WHEN
NEW COLOR APPEARS
DONE
BACK
HOME
ENGLISH
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
WARNING
WARNING
DREMEL 3D40 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
Quick Start Guide
USB Cable
USB Flash Drive
Unclog Tool
Guide Tube Filament Extruder Intake
5
5
!
FEED FILAMENT
NEXT
BACK
HOME
8
8