Dremel Idea Builder 3D20-01 빠른 시작 매뉴얼

{카테고리_이름} Dremel Idea Builder 3D20-01에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dremel Idea Builder 3D20-01 2 페이지.
Dremel Idea Builder 3D20-01에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄
Dremel Idea Builder 3D20-01 빠른 시작 매뉴얼
Find Quality Products Online at:
3D20
Quick Start Guide
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
WARNING
WARNING
DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
1
Unboxing
1
2
3
4
5
6
Firmly lift the build platform
to the top position
3
Getting to Know Your Dremel 3D20
8
1
6
2
7
4
3
15
16
14
13
17
18
9
11
10
12
4
Getting Ready to Build
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
WARNING
WARNING
INSTRUCTIONS WHEN USING THE DREMEL 3D20.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position, remove the lid
and remove the build platform.
2. Place filament spool onto spool holder with spool being fed from
the bottom towards the back of the Dremel 3D20. Insert spool
lock into spool holder and rotate 90 degrees to lock in place.
3. Thread filament through filament guide tube.
4. Insert the filament coming from the filament guide tube into
the extruder intake (top).
5. Adhere build tape over the build platform.
6. Install platform using 3 clips. Place the table under the two
back clips then snap it in with the front clip.
7. Plug power cord into outlet and turn on power switch.
8. Tap "Tools" on your Dremel 3D20's touch screen, then tap
"Filament" , then tap "Load Filament" and wait for the extruder
to heat.
9. Once heated, filament will be drawn through the extruder. Allow
filament to exit the extruder for 10 seconds before tapping the
return arrow to complete.
SIDE 1
GlobalTestSupply
www.
ENGLISH
2
Kit Contents
3D20
Quick Start Guide
WARNING
WARNING
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
Dremel 3D20
Instruction Manual
Quick Start Guide
1 Filament Spool
Spool Lock
Power Cable
USB Cable
SD Card
Adjust the platform until
leveling tool slides between
the extruder and platform
with some resistance
0.3mm
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
LEVELING SHEET
Build Tape
Object Removal Tool
Unclog Tool
Leveling Sheet
TIP:
Save your Dremel 3D20 packaging for future transportation
and storage.
1.
Lid
2. Door
3. Touch Screen
4. Build Platform
5. Build Platform Clips
6. Filament Spool
7.
Filament Spool Holder/Lock
8. Extruder Tip
9. Extruder Fan
5
10. Extruder
11. Extruder Intake
12. X-Axis Guide Rails
13. Stepper Motor (1 of 3)
14. Z-Axis Guide Rail
15. Filament Guide Tube
16. Y-Axis Guide Rails
17. SD Card Input
18. USB Input
19 20
19. Power Switch
20. Power Input
LIFT
1
2
Filament
Guide
4
3
5
8
.com