Andrew TYPE 900 조립 지침 매뉴얼 - 페이지 3
{카테고리_이름} Andrew TYPE 900에 대한 조립 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andrew TYPE 900 8 페이지. 90cm, 1.0m & 1.2m smc antenna system
Andrew TYPE 900에 대해서도 마찬가지입니다: 조립 지침 매뉴얼 (16 페이지)
페이지 인쇄
HARDWARE SORTER
M8 x 60mm Round Head Square Neck Bolt
M6 x 30mm Hex Head Bolt
M4 x 12mm Phillips Head Screw
M4 x 10mm Phillips Head Screw
Hardware illustrations are true size.
Place actual hardware on top of illustration to identify.
12
M6 Tapping Screw
M8 x 20mm Round Head Square Neck Bolt
M8 x 30mm Round Head Square Neck Bolt
Washer, Flat -
" x
" OD
Washer, Flat -
" x
" OD
WATCH FOR WIRES! Installation of this product near power lines is dangerous. For your own safety, follow these
important safety rules.
1. Perform as many functions as possible on the ground.
2. Watch out for overhead power lines. Check the distance to the power lines before starting installation. We recommend
you stay a minimum of 6 meters (20 feet) from all power lines.
3. Do not use metal ladders.
4. Do not install antenna or mast assembly on a windy day.
5. If you start to drop antenna or mast assembly, get away from it and let it fall.
6. If any part of the antenna or mast assembly comes in contact with a power line, call your local power company.
DO NOT TRY TO REMOVE IT YOURSELF! They will remove it safely.
7. Make sure that the mast assembly is properly grounded.
Assembling dish antennas on windy days can be dangerous. Because of the antenna surface, even slight winds
create strong forces. For example, a 1.0m antenna facing a wind of 32 km/h (20 mph) can undergo forces of 269 N
(60 lbs). Be prepared to safely handle these forces at unexpected moments. Do not attempt to assemble, move or
mount a dish on windy days or serious, even fatal accidents may occur. ANDREW is not responsible or liable for dam-
age or injury resulting from antenna installations.
INTRODUCTION
This manual covers the installation of the
ANDREW
1.2m SMC antenna system with AZ/EL cap mount and Ku-
single polarity feed.
ASSEMBLY TOOLS REQUIRED
The following list of tools are those required for hand assembly and installation of the antenna.
1 - Ratchet Wrench ( " Drive)
1 - 10mm Nut Driver
1 - 13mm Open/Box End Wrench
1 - Phillips Screwdriver
SITE SELECTION
The first and most important consideration when choosing a prospective antenna site is whether or
not the area can provide an acceptable "look angle" at the satellites. A site with a clear, unobstructed view from a suitable
roof or wall facing south, southeast or southwest is required. Your antenna site must be selected in advance so that you
will be able to receive the strongest signal available. To avoid obstructions, it is important to conduct an on-site survey with
a portable antenna.
As with any type of construction, a local permit may be required before installing an antenna. It is the owner's
responsibility to obtain any and all permits.
BOLT TORQUE
GRADE 8.8 (8G) - YELLOW COLOR
M6
M8
M10
M12
M16
M20
7
18
32
58
144
260
FT-LBS
FT-LBS FT-LBS
FT-LBS
FT-LBS FT-LBS FT-LBS FT-LBS FT-LBS
9.5
24
43
79
195
353
N-m
N-m
N-m
N-m
N-m
N-m
APPLY 24 N-m (18 FT-LBS) OF TORQUE TO M8 BOLT
DANGER!!!
WARNING!!!
1.0m &
For best results in the assembly process, perform each step
in the same sequence as listed in this manual.
1 - 13mm Socket ( " Drive)
1 - Compass
GRADE 2 - SILVER COLOR
#10
IN.
IN.
IN.
IN.
IN.
32
6
11
20
43
92
FT-LBS
FT-LBS FT-LBS
3.6
8
15
27
58
125
N-m
N-m
N-m
N-m
N-m
N-m
APPLY 11 FT-LBS (15 N-m) OF TORQUE TO
IN. 1 IN.
124
259
FT-LBS FT-LBS
168
351
N-m
N-m
1
BOLT