Electrolux 36" Ceramic 사용 및 관리 매뉴얼 - 페이지 11

{카테고리_이름} Electrolux 36" Ceramic에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux 36" Ceramic 26 페이지. 30” and 36” free-standing range hood
Electrolux 36" Ceramic에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (7 페이지), 설치, 사용 및 관리 매뉴얼 (22 페이지), 설치 지침 매뉴얼 (25 페이지), 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

LED MESSAGES OR LIGHT INDICATORS DISPLAYED BY

MAIN CONTROL

CONTROLS LOCK - This feature allows the cooktop to be locked at anytime. Touch and

hold the LOCK key pad for few seconds. If the cooktop is in use, it will be impossible to

enter in the lock mode. All elements need to be turned OFF. When entering in the lock

mode, a beep will sound and the Lock Indicator Light will glow (Fig. 2). Once locked, no

other displays will glow and no Cooking Zones will activate, but the Minute Timer Feature

will be available. To turn the Controls Lock OFF, touch and hold the LOCK key pad for few

seconds. A beep will sound, the Lock indicator light will turn OFF (Fig. 1) and the cooktop

may be used normally.

COOKTOP POWER - The Cooktop POWER key pad activates the entire Cooktop. To

power the cooktop, touch and hold the POWER key pad. A beep will sound and the Power

LED will glow (See Fig. 4). The cooktop will be in a ready mode. If no other key pads are

touched the Cooktop Main POWER will turn OFF automatically. To turn the Main Power

OFF touch and hold the Main POWER key pad. A beep will sound and the Power Indicator

Light will turn OFF (See Fig. 3).

ERRORS CODES XX - The Minute Timer display digits showing an error code. " E - E - E - E - E - " (Fig.

5) and a two digit number error code (Fig. 6) will flash in turn in the Minute Timer display.

LIGHT INDICATORS DISPLAYED BY COOKING ELEMENT

CONTROLS

COOKING ZONE ON/OFF PAD - Each Cooking Elements have separate ON/OFF key

pads. Once the Main Power key pad has been touched to activate the cooktop, touch the

corresponding Cooking Element ON/OFF key pad once to active the Cooking Zone

needed. The indicator light located above the key pad will glow (Fig. 8). If the correspond-

ing hi + (increase), med or - lo (decrease) key pad is not touched, the request to turn the

Cooking Element ON will cancel and the Cooktop Main Power will turn OFF. To set a

Cooking Element power level touch the corresponding Cooking Element hi + (increase),

med or - lo (decrease) key pad once. To turn OFF a Cooking Element, touch the Cooking

Element ON/OFF key pad once. The Cooking Element Indicator Light will turn OFF (Fig. 7).

HOT SURFACE INDICATOR LIGHT - After using any of the single, dual or triple radiant

element positions the cooktop will become very hot. Even after turning the control to OFF, the

cooktop will remain hot for some time. The hot surface indicator light will turn on (Fig. 9) if the

cooktop is still hot and will remain on until the heating surface area has cooled sufficiently. If

the indicator light is on, the control can still be turned ON again for use.

Setting Surface Controls

lock

Fig. 1

Fig. 2

POWER

Fig. 3

Fig. 4

Fig. 5

Fig. 6

ON OFF

Fig. 7

Fig. 8

hot surface

Fig. 9