Electrolux 36" Ceramic 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} Electrolux 36" Ceramic에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux 36" Ceramic 7 페이지. 30” and 36” free-standing range hood
Electrolux 36" Ceramic에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (26 페이지), 설치, 사용 및 관리 매뉴얼 (22 페이지), 설치 지침 매뉴얼 (25 페이지), 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

Important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

IMPORTANT SAFETY

INSTRUCTIONS

• Be sure your cooktop is installed and grounded

properly by a qualified installer or service

technician.

• These cooktops must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA No.

70—latest edition in the United States, or with

CSA Standard C22.1, Canadian Electrical Code, Part

1, in Canada.

The electrical power to the cooktop

WARNING

must be shut off while line connections are being

made. Failure to do so could result in serious injury

or death.

Provide Electrical Connection

Install the junction box under the cabinet and run 120/

240 or 120/208 Volt, AC wire from the main circuit

panel. DO NOT connect the wire to the circuit panel at

this time.

Electrical Requirements

Observe all governing codes and local ordinances.

1. A 3-wire or 4-wire single phase 120/240 or 120/208

Volt, 60 Hz AC only electrical supply is required on a

separate circuit fused on both sides of the line (time-

delay fuse or circuit breaker is recommended). DO

NOT fuse neutral. The fuse size must not exceed the

circuit rating of the appliance specified on the

nameplate.

2. These units can consume up to 9700W at 240 Vac, a

circuit breaker of 40 Amp with wire gauge #8AWG

shall be used.

NOTE: Wire sizes and connections must conform with

the fuse size and rating of the appliance in accordance

with the National Electrical Code ANSI/NFPA No. 70–

latest edition, and local codes and ordinances.

An extension cord must not be used

WARNING

with this appliance. Such use may result in a fire,

electrical shock, or other personal injury.

3. The appliance should be connected to the fused

disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible

armored cable extending from this appliance should

be connected directly to the grounded junction box.

The junction box should be located as shown in

Figure 2 with as much slack as possible remaining in

the cable between the box and the appliance, so it

can be moved if servicing is ever necessary.

4. A suitable strain relief must be provided to attach

the flexible armored cable to the junction box.

Unpacking Instructions

1. Leave corner supports on cooktop until completion

of Electrical Connection.

2. Be sure the bottle of cleaner conditioner packed in

the literature bag is left where the user can find it

easily. It is important that the ceramic-glass

smoothtop be pretreated before use. See Cooktop

Cleaning and Maintenance section in the Use and

Care Guide.

Figure 3