Electrolux 36" Ceramic 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} Electrolux 36" Ceramic에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux 36" Ceramic 25 페이지. 30” and 36” free-standing range hood
Electrolux 36" Ceramic에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (26 페이지), 설치 지침 매뉴얼 (7 페이지), 설치, 사용 및 관리 매뉴얼 (22 페이지), 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

GAS COOKTOP INSTALLATION INSTRUCTIONS

The supply line should be equipped with an approved

shutoff valve. This valve should be located in the same

room as the cooktop and should be in a location that

allows ease of opening and closing. Do not block access

to the shutoff valve. The valve is for turning on or

shutting off gas to the appliance.

Figure 6

Once the regulator is in place, open the shutoff valve in

the gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the cooktop to the

gas supply, check the system for leaks with a manometer.

If a manometer is not available, turn on the gas supply

and use a liquid leak detector (or soap and water) at all

joints and connections to check for leaks.

Do not use a flame to check for leaks

from gas connections. Checking for leaks with a flame

may result in a fire or explosion.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

Check alignment of control knob valves after

connecting the cooktop to the gas supply to be sure the

cooktop manifold pipe has not moved. A misalignment

could cause the valve stems to rub on the control panel,

resulting in a gas leak at the valve.

Disconnect this cooktop and its individual shutoff

valve from the gas supply piping system during any

pressure testing of that system at test pressures greater

than 1/2 psig (3.5 kPa or 14" (35.6 cm) water column).

Isolate the cooktop from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig

(3.5 kPa or 14" (35.6 cm) water column).

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit

protected by a 15 amp circuit breaker or time delay fuse.

Do not use an extension cord with this cooktop.

Grounding Instructions

IMPORTANT Please read carefully.

For personal safety, this appliance must be properly

grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong grounding wall receptacle (see Figure 7) to

minimize the possibility of electric shock hazard from the

appliance.

The wall receptacle and circuit should be checked by

a qualified electrician to make sure the receptacle is

properly grounded.

Preferred Method

Grounding type

wall receptacle

Where a standard 2-prong wall receptacle is installed,

it is the personal responsibility and obligation of the

consumer to have it replaced by a properly grounded

3-prong wall receptacle.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

Cooktop Installation

1. Visually inspect the cooktop for damage.

2. If you are installing the optional Stainless Steel

backsplash, first fix it at the back of the cooktop

using the screws supplied with the kit and follow the

instructions attached.

3. Set the cooktop into the countertop cutout.

NOTE: Do not use caulking compound; cooktop should

be removable for service when needed.

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Power supply

cord with 3-prong

grounding plug.

Figure 7