Bosch 6 Series 사용 설명서 - 페이지 21

{카테고리_이름} Bosch 6 Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 6 Series 28 페이지. 2 door top freezer, inox-easyclean
Bosch 6 Series에 대해서도 마찬가지입니다: 사용자 설명서 (24 페이지), 설치 및 사용 설명서 지침 (20 페이지), 설치 및 사용 설명서 지침 (20 페이지), 설치 및 사용 설명서 지침 (20 페이지), 사용 설명서 및 설치 지침 (48 페이지), 사용 설명서 (16 페이지), 사용 설명서 (48 페이지), 설치 지침 매뉴얼 (27 페이지), 사용 설명서 (12 페이지), 설치 및 운영 지침 매뉴얼 (36 페이지), 사용 설명서 (16 페이지), 설치 및 사용 설명서 지침 (16 페이지), 사용 설명서 지침 (29 페이지), 사용자 설명서 및 설치 지침 (16 페이지), 사용 정보 (32 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용 정보 (28 페이지), 사용자 설명서 (23 페이지), 사용 설명서 (24 페이지), 설치 지침 및 사용 지침 (24 페이지), 사용 정보 (16 페이지), 사용자 설명서 (36 페이지), 사용자 설명서 (32 페이지), 사용자 설명서 (28 페이지), 사용자 설명서 (28 페이지), 사용 정보 (20 페이지), 사용 설명서 (28 페이지)

Bosch 6 Series 사용 설명서
Cleaning
How do I clean the hob?
Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-
water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"

3Trouble shooting

U sually, faults are small matters that are easy to
T r o u b l e s h o o t i n g
eliminate. Please read the information in the table
before calling the after-sales service.
Display
None
The displays flash
The
Ù
indicator flashes in the
hotplate displays
"...
"†
+ heat setting and acous-
tic signal
"†
and acoustic signal
"‚
/
"‡
"‰
"Š‹‹‹
"Š‹‚‹
—...‹‹
Do not place hot pans on the control panel.
Notes
If
appears on the display, press and hold the
"
button for the relevant cooking zone in order to read
the fault code.
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Possible cause
The power supply has been disconnected.
The device has not been connected in accord-
ance with the circuit diagram.
Electronics fault.
The control panel is damp or an object is cover-
ing it.
A fault has occurred in the electronics.
The electronics have overheated and have
switched off the corresponding hotplate.
The electronics have overheated and have
switched off all hotplates.
There is a hot pan in the area of the control
panel. There is a risk that the electronics will
overheat.
There is a hot pan in the area of the control
panel. To protect the electronics, the hotplate
has been switched off.
The hotplate has overheated and switched itself
off to protect the work surface.
The hotplate was operating for an extended
period without interruption.
The supply voltage is faulty; outside of the nor-
mal operating range.
The hob is not connected properly
Solution
Use other electrical devices to check whether a short-circuit has
occurred in the power supply.
Ensure that the device has been connected in accordance with
the circuit diagram.
If the fault cannot be eliminated, inform the technical after-sales
service.
Dry the control panel or remove the object.
To acknowledge the fault, cover the control panel with your hand.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
Remove the pan. The fault display goes out shortly afterwards.
You can continue to cook.
Remove the pan. Wait for a few seconds. Touch any control. If the
fault display goes out, you can continue to cook.
Wait until the electronics have cooled down sufficiently and
switch the hotplate on again.
The automatic safety switch-off function has been activated. See
section
Contact your electricity provider.
Disconnect the hob from the power supply. Ensure that it has
been connected in accordance with the circuit diagram.
Trouble shooting
en
21