Atlantic Technology 8200 System 사용 설명서 - 페이지 7

{카테고리_이름} Atlantic Technology 8200 System에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlantic Technology 8200 System 20 페이지. Pedestal subwoofer systems
Atlantic Technology 8200 System에 대해서도 마찬가지입니다: 검토 매뉴얼 (3 페이지), 사용 설명서 (12 페이지)

페이지 인쇄

Instruction Manual

Remote Control

Figure 8

��

Preset Program EQ buttons

Select from 4 preset equalization settings in any sequence.

(page 14)

Reference EQ button

REF button returns the amplifier to its flat/THX EQ settings and

returns the volume trim level to 0dB.(page 14)

MUTE button

Mutes the output of the amplifier.Pressing again returns the ampli-

fier to the previous volume setting

Level TRIM buttons

The  button increases and the  button decreases the volume

of the PedWoofers above or below the preset reference level in 1dB

increments.(page 14)

��

�

��

Connecting Your PedWoofers

The Atlantic Technology PedWoofer System is relatively simple to hook

up. In all cases, the PedWoofers should be connected to their dedicated

amplifier using high quality 2-conductor speaker wire (min. 16ga.

for runs of 30ft. or less; 30-100ft. use 14ga; Over 100ft use 12ga.) The

remote sensor connector on the back of the PedWoofer is connected to

the dedicated amplifier using the included plug-in connectors and any

good quality stranded 3-conductor wire (minimum 20ga; for lengths

over 200 ft.use 18ga.).

WARNING: To prevent risk of electrical shock or damage to your

equipment, always unplug all component AC cords before pro-

ceeding with speaker and component connections! The last step in

wiring your system should be plugging in the AC cords!

Low Level Connection (LO IN)

We suggest using the low level (RCA jack) subwoofer line out or preamp

output if your receiver/processor has one.This jack may be labeled Sub,

Subwoofer,or LFE (Low Frequency Effects).Simply connect to the LO IN

jack(s) on your SA-8200 or SA-6200 amplifier with high-quality shielded

cables as shown in Figures 9-11. Please consult your processor/receiver

manual for further information regarding the use of these outputs.

Using the Low Level Thruput (THRU)

If your processor has a single subwoofer output and you are using the

SA-8200 Dual Mono amplifier,connect it using the example in Figure 9 to

connect both channels of the amplifier.We have supplied a short jumper

to facilitate this connection method.The THRU jack(s) can also be used

to run the low-level signal through the amplifier and out to another unit,

as shown in Figure 8. The signal that comes out of the THRU jack(s) is

identical to the input signal.

High Level Connection (HI IN – SA 8200 only)

Alternately,if you are connecting the amplifier through the high level (HI

IN) inputs,follow the diagram in Figure 12.If you do,we recommend that

you use high-quality speaker wire of at least 18 gauge or heavier. Please

consult your audio/video specialist for more specific wire information.

You can connect to the HI IN inputs by using a variety of audio type

connectors,or by removing 1/2" of insulation from each wire end,twist-

ing the individual strands of each conductor together, placing the wire

through one of the post holes and screwing down the nut snugly (but use

care not to over tighten them).

It's important to observe polarity while making speaker connections:

red (+) terminals on the amplifier to red (+) on the speaker, black (–)

on the amplifier to black (–) on the speaker. Note that one wire in each

pair will be marked by either the conductor color, printing on the wire

jacket,a ridge on one side of the wire jacket,or a thread intertwined with

the wire strands.By convention,the marked wire is connected to the red

(+) terminal.

Connecting Your PedWoofers