Atlas STRATEGY SERIES FAP42T 설치 지침

{카테고리_이름} Atlas STRATEGY SERIES FAP42T에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlas STRATEGY SERIES FAP42T 1 페이지. Strategy series ii
Atlas STRATEGY SERIES FAP42T에 대해서도 마찬가지입니다: 브로셔 (5 페이지), 일반 설명 (3 페이지), 매뉴얼 (5 페이지)

페이지 인쇄
Atlas STRATEGY SERIES FAP42T 설치 지침
FAP42T
Installation
Instructions
Mounting Template
9" Dia.
enclosure. Terminate the service loop to Phoenix style connector provided (please note polarity). Combination
6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg
7. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
9. For safety and seismic considerations a suspension ring is integrated into input panel section of unit. Atlas Sound strongly suggests
that a support wire be installed from this support point to a suitable anchor point above ceiling grid. In drop tile applications, this wire
2. Place tile bridge rails and C-ring through hole. Use V shaped edge of C-ring to align tile bridge assembly above ceiling (alignment screws
3. Bring service loop from through the tile bridge/C-ring to access panel located on side of the enclosure. Terminate service loop to Phoenix style
4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg assemblies until they engage the C-ring assembly.
5. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
Use of optional FAP42-TR
in new construction. Bracket mounts between 16" or 24" OC studs and includes a 3/8" downward lip to provide a template for drywall installers to cut
Note: tile bridge components are not used in new construction applications where new construction bracket is utilized.
1. Bring service loop through hole in ceiling provided by pre construction bracket to access panel located on side of Enclosure.
Terminate service loop to Phoenix style connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
2. Insert speaker assembly into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dog leg assemblies until they engage
3. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)
Input
Auxillary
Suspension
Point
GRILL REMOVED FOR CLARITY
Dog Leg
In Normal
Position
Tile
Bridge
Ceiling Material up to 1
/
"
1
4
The Atlas Sound Strategy Series
construction drop ceiling or drywall materials
1. Remove 2'x2' or 2'x4' tile.
2. Align adjustable dual rail & c-ring assembly on rear of tile in desired position.
3. Using template provided mark cutout circle with marker and cut hole. (9" FAP42T)
4. Affix C-ring assembly to rails using screws provided and position assembly on rear of ceiling
tile. Replace tile into grid making sure that formed ends of tile bridge rails engage T-bar tile support rails.
5. Bring service loop from rear of tile, through tile bridge C-ring to access panel located on side of
knockouts are provided to facilitate conduit.
assemblies until they engage C-ring assembly. DO NOT OVER-TIGHTEN DOG LEG SCREWS!
8. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
can usually be installed from an adjacent tile access near speaker location.
Dry Wall ("Hard Deck") Installation
1. Using template provided, mark cutout circle in desired mounting location and cut hole. (9" FAP42T)
provided are not required for this type of installation)
connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
DO NOT OVER-TIGHTEN DOG LEG SCREWS!
6. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
New Construction (Darywall Ceilings)
1
(for use with FAP42T) new construction bracket essentially reserves speaker mounting location prior to drywall installation
around. For final installation, please follow instructions below.
ring provided on new construction bracket. DO NOT OVER-TIGHTEN DOG LEG SCREWS!
4. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
Typical Parallel Hookup of Full Range 70.7/100V Speakers
Amplifier
Typical 120Watt 70.7V Output
Tap Wattage Total : 64 Watts
1
2
3
4
5
6
master
power
power
Auxillary
Suspension
1 FAP42-TR Has not been evaluated by UL Laboratories
Point
NOTE: Dog legs will accommodate ceiling material thickness up to 1 1/4" as shipped from factory.
For thicker ceiling materials (up to 2") simply unscrew and flip dog legs as shown.
DO NOT OVER-TIGHTEN DOG LEGS IN EITHER CONFIGURATION!
NOTE: UL recognized conduit clamp must be used for conduit
Dog Leg
connections. Cable connection cavity is not intended to be used
In Inverted
Position
FREQUENCY RESPONSE: 70Hz-20kHz
Ceiling Material up to 2"
®
II assembly mounts easily into existing
Drop Tile Ceiling
Installation
NOTE: *DO NOT USE 8Ω SETTING WITH 70.7V/100V SYSTEMS! *DO NOT
OVERPOWER IN 8Ω CONFIGURATION! AMPLIFIER OUTPUT SHOULD NOT
EXCEED 16W RMS @ 8Ω PER SPEAKER
-
-
+
+
+
Auxillary
-
Suspension
FAP42T
FAP42T
Point
Full Range
Full Range
16W @ 70.7V
16W @ 70.7V
Dog Leg
as a junction box.
Tile
In Normal
Bridge
Position
SENSITIVITY: 88dB (1W/1M)
Ceiling Material up to 1
ATS001131a RevF 12/08

Installation Instructions

Painting Shield
8
⁄
" Dia.
1
2
-
-
+
+
FAP42T
FAP42T
Full Range
Full Range
16W @ 70.7V
16W @ 70.7V
Dog Leg
In Inverted
Position
Tile
Bridge
/
"
Ceiling Material up to 2"
1
4
FAP42T
ATS001131a RevD 2/04
Auxillary
Suspension
Point
Tile
Bridge