Atlas 200 Series 매뉴얼 - 페이지 2

{카테고리_이름} Atlas 200 Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlas 200 Series 12 페이지. Floor-standing cabinets
Atlas 200 Series에 대해서도 마찬가지입니다: 설치 지침 (1 페이지)

페이지 인쇄

100, 200, 500, 700, & FMA Series

1. Important Safety Instructions

a. These cabinet products are initially provided without installed electrical equipment and therefore are not liable for any hazards/damage

incurred by not following proper safety procedures. Installation, operation, and maintenance personnel should always follow the procedures

outlined in the National Electrical Code and any other regulations mandated by the local authorities having jurisdiction over the installation.

b. The cabinet is designed for installation and use in areas designated as "Restricted Access Location" only.

c. The installation of the cabinet is to be made by qualified service personnel in accordance with local building codes, the Installation

Instructions, and the National Electrical Code.

d. The Listing Mark on the product does not cover any of the electrical equipment, AC or DC, that may be installed in the field. The Product is

not intended to contain or house any open-frame, high-voltage electrical components like open switches, supplementary protectors, circuit

breakers, fuses, relays, etc.

e. The cabinet is intended to house audio, video, information technology, and telecommunications equipment provided with their own fire,

electrical, and mechanical enclosures.

f. Product is evaluated for use in environmentally controlled indoor areas only. The product is not to be used outdoors, in industrial or harsh

environments, or in plenum spaces.

g. The frame of the product may support a maximum load of 2,500 lbs.

h. Use eye protection and protective gloves while unpacking and installing the cabinet.

i. Ensure adequate manpower is available to safely unload and install the product.

2. Introduction

a. This rack cabinet system is used to house rack-mounted equipment for use in audio, video, and/or data applications for network, voice,

data and video modules/devices and their associated cabling. Final equipment installer must follow individual equipment manufacturer's

installation instructions.

b. The 100 Series stand-alone cabinet is the most economical cabinet and features fixed rails.

c. The 200 Series is also a stand-alone cabinet; however, the fixed rails are replaced with fully adjustable rails.

d. The 500 Series is an open frame cabinet, gangable, designed to facilitate joining multiple cabinets together. The open frame also facilitates

wiring and wire passage.

e. The 700 Series is a gangable cabinet and when used with the optional SBK-700 Seismic Bracket Kit, is certified to meet Telcordia

Technologies GR-63-CORE Issue 3 Earthquake Compliance. With brackets properly installed, the 700 series cabinets may support up to 625

lbs of equipment during a Zone 4 earthquake motion, which is comparable to a Richter Magnitude 8.0 earthquake.

f. The FMA Series is a feature-rich cabinet designed for maximum utility. It is available as either a stand-alone or gangable cabinet.

g. All of these cabinet frames may support a maximum load up to 2,500 lbs.

h. These cabinets all comply to U.S. and Canadian (Bi-National) Standard for Safety of Information Technology Equipment, CAN/CSA-C22.2 No.

60950-1-07, Second Edition, date March 27, 2007, UL 2416, Outline of Investigation for Audio/Video, Information and Communication

Technology Equipment Cabinet, Enclosure and Rack Systems.", Issue 2, dated 2013-07-12.

3. Required Tools

a. Razor Knife

b. #2 Phillips Cross-Drive Screw Driver (Manual or Auto)

⁄

" Hex Socket Driver

d. Tape Measure (optional)

e. If installing Front Door (purchased separately) -

1601 JACK MCKAY BLVD.

ENNIS, TEXAS 75119 U.S.A.

Floor-Standing Cabinets

⁄

L-Shaped Hex Driver Key

TELEPHONE: (800) 876-3333

FAX: (800) 765-3435

2/12

AtlasSound.com