Atlas 500 Series 매뉴얼 - 페이지 5

{카테고리_이름} Atlas 500 Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlas 500 Series 12 페이지. Floor-standing cabinets
Atlas 500 Series에 대해서도 마찬가지입니다: 설치 지침 (1 페이지)

페이지 인쇄

100, 200, 500, 700, & FMA Series

g. If required, the rotation and lock position may be changed to suit the user:

Open the door.

ii.

Remove the bolt in the back of the lock.

iii. Carefully remove the lock cam and lock washer.

iv. Behind the lock cam is a special 90° washer. This washer

has a section removed and controls the lock and unlock

orientations by engaging on a protrusion on the lock body.

Carefully remove this special 90° washer.

Insert the key into the lock and orient to the desired locking

position.

vi. Replace the special 90° washer and then turn the key to the

unlocked position. Repeat using different orientations until the

desired locking and unlocking orientations are met. Note: The washer can be flipped if needed.

vii. Replace the lock cam, lock washer and bolt to match the desired locking and unlocking orientations.

9. Leg Levelers (presence varies with product or purchased separately)

CAUTION: Before loading the cabinet with equipment, note the use of the leg levelers reduces the cabinet capacity. They are not recommended for

installations requiring full load capacity.

a. In most cases where cabinet is to be mounted to the floor, remove the Leg Levelers from the cabinet by turning them in a counter-clockwise

fashion.

b. In cases where multiple cabinets are to be ganged together, remove the Leg Levelers as they can interfere with the adjoining cabinet.

c. In cases where the caster kits are used to move the cabinet, remove the Leg Levelers as they can catch on the ground surface and cause the

cabinet to fall over.

10. Caster Kits (purchased separately)

DID YOU KNOW? Caster Kits may be purchased to transfer an empty cabinet. The load capacity of these

Caster Kits is 1000 lbs. for the 100, 200, 500 and 700 Caster Kits. The FMA Caster Kit capacity is 880 lbs.

NOTE: Interference could exist between racked-equipment and caster. See Initial Rail Setup section before

proceeding.

CAUTION: Tall rack cabinets are not stable during any transport and the cabinet can easily fall over. This condition

can be worse with the equipment and weight within the rack. Do not move a loaded cabinet on a caster kit.

Take great care with moving an unloaded cabinet on a caster kit. Please use an appropriate number of people or

appropriate equipment to safely handle the weight.

a. It is best to install the caster kit on an unloaded cabinet.

b. Carefully lay the cabinet on its side.

c. 700 Series cabinets:

Install individual casters on the diagonal gussets located on the cabinet bottom. Use (4) of the

⁄

-20 x .625" carriage bolts and

d. 100, 200, and 500 Series cabinets:

Locate the (4) caster installation points on the cabinet bottom.

ii.

Loosely install the (16)

cabinet interior.

iii. Mount a metal stiffener bracket over a pair of the caster install points. The bracket will be oriented from front-to-back. Both brackets will

be used to stiffen each side of the cabinet. Be sure the (2) edge flanges on the brackets are pointing towards the outside of the cabinet.

1601 JACK MCKAY BLVD.

ENNIS, TEXAS 75119 U.S.A.

Floor-Standing Cabinets

⁄

-20 KEPS nuts to attach each caster.

⁄

-20 x .625" carriage bolts through each caster installation point. The bolt head should be installed inside the main

Lock Body

90° Washer

"New" Lock Cam

Lock Washer

(May Not Be Present If Assembly

Has A Serrated Head Bolt)

TELEPHONE: (800) 876-3333

FAX: (800) 765-3435

Bolt

700 Series Installation

Lock Cam Detail

AtlasSound.com

5/12