Alereon AL5740 Honolulu 사용자 설명서 - 페이지 2

{카테고리_이름} Alereon AL5740 Honolulu에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Alereon AL5740 Honolulu 5 페이지.

페이지 인쇄

Honolulu User's Guide

exe file. Please follow the following steps in order to install Alereon's Wireless USB Manager.

Note: In some cases, separate driver packages will be included for the various supported operating systems.

Step 3: Run the DisplayLink installer.

Step 4: Reboot the PC. If you choose not to reboot, the Honolulu video output may not work correctly until a reboot is

completed.

2.0

STABLISHING A

Step 5: Open the Wireless USB manager and select the "Connection Rules" tab.

Step 6: Click the On/Off button under "Wireless Associations". The button should turn green. If this button is disabled, please

ensure that the HWA drivers are properly loaded. Please see the Wireless USB Manager User's Guide.

Step 7: Connect the power cable to the AL5740 Honolulu board. You must do this within 3 minutes after enabling wireless

associations in the Wireless USB Manager.

Step 8: After a few seconds, the Wireless USB Manager should report that a device wants to wirelessly associate. When this

happens enter the PIN "Alereon!". The A is capitalized and there is an exclamation mark at the end. The quotes are not part

of the PIN.

Step 9: The PIN association should succeed and the in a few seconds the device should connect and enumerate. If the PIN

association was successful but the device fails to connect, power cycle the device and it should connected within a few

seconds. If for any reason this process fails to prompt you for a PIN please remove the HWA and remove power from the

Honolulu board, then repeat steps 5 to 8.

Step 10: Your Honolulu adapter should now have a wireless connection to the host PC. Connect a monitor or TV using a VGA

or HDMI cable and enjoy.

3.0

SAGE

OTES AND

•

Optimal Resolution for Video performance - The DisplayLink drivers perform more advanced video compression when TV specific

resolutions are used. When typical PC resolutions are used, the video performance may be degraded in some cases. The recomm-

mended output resolutions for the Honolulu board are 640X480, 720x480, 800x600 and 1280x720. Choosing other resolutions could

degrade video performance.

•

Changing the Resolution (Windows XP and Vista) - You can change the resolution of the Honolulu attached display using the Dis-

playLink Manger which can be found in the Windows system tray. The icon has a blue monitor with a wire attached. An example is pro-

vided to the right of this paragraph.

•

Changing from Mirror to Extended Mode (Windows XP and Vista) - You can change the mode of the Honolulu attached display

using the DisplayLink Manger which can be found in the Windows system tray. In Mirror mode, the image and resolution of the main

display is also used on the second display. In extended mode, the resolution output of the Honolulu can be changed indepen-

dently of the main PC display.

•

Windows 7 - The Mode and resolution of the Honolulu attached display must be changed through the display resolution settings

included in Windows 7. To access this functionality right click on the desktop and select "display resolution".

•

Playing Full Screen Video in Windows XP - The DisplayLink drivers have a limitation when playing full screen Flash video. Typical

examples of Flash video are YouTube and Hulu. The workaround for this is to disable hardware acceleration in the flash video. On most

PC's this changed is retained by the flash player, so these steps should need to be performed only once. Here are the steps to perform

this workaround:

•1. Right click on the flash video, select Settings

•2. Go to the Display card

•3. Uncheck "Enable hardware acceleration"

•

IRELESS

ONNECTION

ECOMMENDATIONS

Rev. 1.0

Confidential