Bose 802 빠른 매뉴얼
{카테고리_이름} Bose 802에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose 802 2 페이지. Iv series
Bose 802에 대해서도 마찬가지입니다: 설치 매뉴얼 (13 페이지)
페이지 인쇄
• Modular components for system design flexibility
• High linear excursion and power output
• Electronic systems controller
Technical Information
Frequency range
55Hz – 16kHz
Active equalization
(with 802C Series II systems controller)
Required
Nominal impedance
8Ω
Maximum acoustic output
114dB-SPL average, 123dB-SPL peak
Power handling capacity
240W continuous pink noise, 55Hz – 16kHz
Recommended amplifier power
240W minimum, 480W maximum
Sensitivity
Full-range, 91dB-SPL (1W, 1m)
Horizontal beamwidth
120°
Vertical beamwidth
100°
Enclosure construction
Mica-reinforced polyethylene copolymer
structural foam
Fusing
Built-in 4-ampere quick-acting fuse
(replaceable)
Insert locations
Four M8 (8 mm)
Connectors
Two (2) parallel-wired
1
⁄
" (6.3 mm) phone
4
jacks and two (2) parallel-wired male XLR
connectors
Dimensions
13" (H) x 20
1
⁄
" (W) x 12
1
⁄
" (D)
2
2
(33 x 52 x 32 cm)
Weight
31 lb (14 kg)
Bose
802
Series II
®
®
Loudspeaker
General Description
The Bose 802 Series II sound components
provide a fully modular system designed
for high quality reinforcement of voice
and music.
Bose 802 Series II loudspeakers work with
the 802C Series II systems controller for
active equalization of the system. The 802
Series II loudspeaker is preferred for
applications requiring a rugged, portable
enclosure, but can be used in permanent
indoor sound system installations.
The 802C Series II systems controller assures
smooth, accurate spectral response across
the entire operating range of the 802
Series II loudspeaker. Sharp subsonic and
ultrasonic band-limiting filters reduce
power waste, stage noise, high-frequency
instability, and interference. The systems
controller also provides two independent
signal channels.
Component Description
Each 802 Series II loudspeaker uses
eight 4
1
⁄
" full-range drivers mounted in
2
symmetric vertical pairs on a faceted
®
Articulated Array
baffle assembly. The
drivers feature low-impedance,
edge-wound aluminum voice coils,
12-ounce Ferrite V ceramic magnets, and
molded polyester frames. Their advanced
cone and motor system give them high
linear excursion capability and power
output.
Tuned reactive air columns reduce
distortion by controlling the cone
excursion required to reproduce deep bass
frequencies. A built-in directivity control
circuit maintains the vertical dispersion
pattern through the high-frequency range.
It also protects the drivers from
high-frequency overload.
The 802C Series II systems controller is a
single-rack sized device. It is capable of
providing crossover functions, active
electronic equalization, and dual channel
signal processing for both the 802 Series
II loudspeakers and the 502
Acoustimass
®
enclosure. It features
-10/+4dB-V input sensitivity switches,
all-balanced inputs and outputs, -18/+3dB
bass level control, and a bass mono sum
switch. It also provides automatic output
muting on turn-off, and a secure
rear-panel operating mode switch.
®
B or 502BP