Bose Lifestyle 48 문제 해결 매뉴얼 - 페이지 19

{카테고리_이름} Bose Lifestyle 48에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose Lifestyle 48 32 페이지. Personal music center ii - owner's guide
Bose Lifestyle 48에 대해서도 마찬가지입니다: 설치 매뉴얼 (42 페이지), 매뉴얼 (29 페이지), 설치 매뉴얼 (36 페이지), 소유자 매뉴얼 (25 페이지), 소유자 매뉴얼 (24 페이지), 소유자 매뉴얼 (13 페이지), 빠른 설정 매뉴얼 (3 페이지), 소유자 매뉴얼 (30 페이지)

2.16 Audio Signal Path Flow

All audio input must come into the bass module via the S/PDIF input on the RJ-45 connector. This

signal is received and converted into two channels of audio data in serial format using a single

data line that carries both the left and right audio sample data, one after another, a frame clock (to

tell whether the data is right or left), and a bit clock. The S/PDIF receiver also generates a Master

audio clock, running at 256 times the audio sample rate. Also, useful information embedded in the

S/PDIF stream, such as pre-emphasis on/off and compressed data on/off, are stripped out and

communicated to the Sharc.

The two channels of audio, whether they are stereo PCM information or compressed multichannel

audio, are sent to the CS49329 (U103) Compressed Audio Decoder. The format of the incoming

data is determined and the Sharc downloads the appropriate decompression program to the

CS49329 (either PCM pass-thru, AC-3, or DTS). The CS49329's DSP then performs the neces-

sary decompression and recovery of the audio data and sends up to 6 channels of audio out on

three separate serial data lines, using the same serial format as the S/PDIF receiver.

The up-to-six channels of audio from the CS49329, along with their corresponding audio clocks

are inputted into the Sharc, where Videostage

limiting, tone controls, volume, etc. are performed on them. The audio data is processed in 256

sample blocks such that one block of audio data is being fed out to the D-to-A converter while the

next block is being processed.

The Sharc sends the up-to-six channels of audio out to the audio codec whose D-to-A converters

generate the analog audio signals that end up at the audio power amplifiers.

2.17 Signal Processing

The details of the signal processing are beyond the scope of this document, and only a general

overview of the processing is presented here. There are no user controls on the bass module as

all volume, tone, etc. control is accomplished via the head-end and remote control.

The basic signal processing (EQ and Videostage 5) are essentially identical to that used in the

Lifestyle

Series II digital bassboxes. As with the Series II systems, volume and tone control,

dynamic equalization, etc. all accomplished in the digital domain. The compressed format audio

streams (AC-3 and DTS) are decoded by a separate DSP from the Sharc used to perform the

Bose

processing.

2.18 Power On and Boot Up Sequence of Events

When power is first applied, the Sharc boots and loads/executes the first set of instructions found

in the FLASH memory. This code is very basic and only runs power on self tests (POST) that

check basic communications with all the hardware peripherals (U2, U103, U301, U302, U303, and

U401) and computes the version and checksum of the code in FLASH. If all appears to be "well",

the Sharc reboots and loads the actual program code that makes it function as a LS28/35 bass

module. If the POST fails, the Sharc signals this by rapidly flashing (approx. 3Hz rate) the amber

and green LEDs alternately for a couple of seconds and then performs a Reset and tries again.

Theory of Operation

processing, equalization, dynamic equalization,

PS18/28/35 Troubleshooting Guide