Bose 3-2-1 문제 해결 매뉴얼 - 페이지 8

{카테고리_이름} Bose 3-2-1에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose 3-2-1 28 페이지. Home entertainment system
Bose 3-2-1에 대해서도 마찬가지입니다: 소유자 매뉴얼 (44 페이지), 빠른 설정 매뉴얼 (1 페이지)

페이지 인쇄

3. Communications Busses and Interface Blocks

3.1 Communications Busses

3.1.1 I

C Bus

There are two I

C buses: (1) the I

is J7000-NV which is not populated in production; (2) the I

configures the devices in audio path. The devices connecting to the I

and its protocol are listed in following table.

Reference

Vendor

Designator

Number

U4000

TEA6422

U8001

AK4112B

U9200

AK4382A

*Note: "w" bit can be either 1 or 0 depending on read/write.

3.1.2 SPI Bus

The CS98200's (U7003) built-in SPI interface is used to control two subsystems in the

console, the VFD (interface connector is J6500 [sheet 13, B8]) and the Tuner Assembly

(interface connector is J6000 [D8]). U6802 [A-C6] is the buffer between CS98200 and the

two subsystems. These subsystems must timeshare the SPI resource.

For the outbound data (data stream from CS98200 to subsystems), both subsystems have a

signal which uniquely identifies when the SPI data sent from the CS98200 is valid for them.

For the VFD module, the VFD_STROBE indicates it is the target. For the Tuner Assembly,

it is SPI_SEL (which becomes TNRBD_SEL once buffered). These signals are the key to

timesharing the SPI bus. Note the differing polarities associated with the signals.

For the outbound data (data stream from subsystems to CS98200), each subsystem inter-

acts with the CS98200 differently, as follows:

• The VFD module allows for bi-directional communication, but timeshares a single wire in

half-duplex mode to accomplish this. To receive SPI data from the VFD, the CS98200 must

therefore use the SPI configuration option which allows receiving on the same pin used for

transmission (pin 196). See the CS98200 register spec for details.

• The Tuner Assembly will use SPI in true bi-directional, full duplex mode, although the

CS9200 will be the master of all transfers. The TNRBD_DATAIN signal, which ties to the

CS98200's SPI receiver, is used for receiving. Again, see the CS98200 register spec for

SPI configuration details.

THEORY OF OPERATION

C Debug bus for software development, the connector

Protocol

Address

Byte

10011010b

AKM

00wxxxxxb

AKM

011xxxxxb

C configuration bus which

6-input stereo analog audio input MUX chip (ST). No

CS pin is available on this part. ADDR pin has an

internal 50K pull-up: logic high.

S/PDIF receiver. Uses the AKM_CS chip select signal

to differentiate its messages from I

address separates its messages from those for the

mix-down DAC. "w" is the write bit. The 8 data bits of

the 16-bit protocol are driven by the AK4112B when w

is 0.

Stereo DAC for the CS98200 Mix-down path. Uses

the AKM_CS chip select signal to differentiate its

messages from I

C. The AKM address separates its

messages from those for the S/PDIF receiver.

C configuration bus

Description

C. The AKM