Bose FreeSpace E4 Series II 빠른 시작 매뉴얼

{카테고리_이름} Bose FreeSpace E4 Series II에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose FreeSpace E4 Series II 4 페이지. Business music system
Bose FreeSpace E4 Series II에 대해서도 마찬가지입니다: 소유자 매뉴얼 (18 페이지), 소유자 매뉴얼 (16 페이지), 소유자 매뉴얼 (15 페이지), 소유자 매뉴얼 (33 페이지)

페이지 인쇄

Connect your PC to the E4 system

• NOTE: Install your FreeSpace

system Installer™

software before following these steps.

RS232

SENSE MICR

OPHONES

ion.

RS232

CLASS 2 WIRING

AMP OUT

WALL PLA TE CONNECTION

INPUTS

OUTPUTS

CONTAC T

MUSIC ON

CLOSURE

AUX OUT/

HOLD/

AMP OUT

INPUT

CONTR O L

PBX OUT

12V

AUDIO SOURCES

MIC/

MIC/P AGE/

DIRECT IN /

LINE 1

LINE 2

LINE 3

LINE4

CONTR O L

LISTED 917D

geprüfte

V Rheinland

Sicherhei t

AUDI O

EQUIPMENT

This device complie s with part 15 of the FCC rules. Operatio n is

subject to the following conditions : (1)Thi s device may not cause

harmful interference and (2)this device must accept any interferenc e

PTT

received,inc luding

interference whic h may cause undesired operat

Complies with Canadian ICES-003 Class

Spec .

• Connect a straight-wired DB9M-to-DB9F cable between

the COM port of your PC and the RS-232 port of the

E4 system.

• Make sure the E4 system POWER switch is set to ON.

Set zone Speaker EQ

• Select ZONE Set Up for each zone output.

• Select the proper loudspeaker EQ type from the

Speaker EQ drop list.

Assign sources to zones

• Select Source Assign for each zone.

• Move selected System Sources to the ZONE Sources

list using the right arrow button.

• In the Zone Sources list, double click on the name of

the source you want as the default source.

• Assign Paging to a zone by adding the PAGE source.

• Make sure all zones are connected to the E4 system.

Calibrate Auto Volume

• Check that the Auto Volume sensing microphone has

been installed according to recommendations.

• Select Auto Volume for the zone to be calibrated.

• Set the Auto Volume Tracking level. Use a level of

"less than" by "3" or "6" dB for background systems,

and a level of "equal to" or "more than" by "1" or "3" dB

for foreground systems.

FreeSpace

E4 Series II System Quick Start-Up Guide

Start the Installer software

RISK OF ELECTRICA

S HOCK

RISQUE DE CHOC ELECTRIQUE

DO NO T O PE N

NE PA S O UVRIR

POWER

OFF

OUTPUT

VOL TAGE

70V

100V

100/120V~AC T6.25A, L250V

220/240V~AC T3.15A, L250V

DO NO T SWITCH

50/60Hz

WHILE POWER IS ON

300W MAX

FreeSpace E4 Series II

400 Watt System Electronics

Bose Corporation, Framingham, MA 01701-9168

• Launch the Installer software on your PC.

Made in the U.S.A.

• NOTE: The software installation disc is included with

the E4 system hardware.

• When the connection is initialized, the Installer software

automatically switches the E4 unit from standby to

operating mode.

• Once the connection is established, the Hardware Set

Up window for the E4 system appears on the screen.

Set Input Gain for music sources

• Select In Gain for the first music source.

• Select the proper input type from the Type drop list.

• When using sources that have an output gain control,

increase the source output gain until the signal meter is

solid green. Occasional flashing red is normal.

Set zone Output Gain

• Select Out Gain for each zone.

• Raise the Gain slider to the desired maximum volume

and move the Maximum Gain Stop to this location.

• Lower the Gain slider to the desired minimum volume

and move the Minimum Gain Stop to this location.

• Set the Gain slider to the desired initial volume.

• Click the Set Up button to start the calibration process.

• Follow the onscreen instructions during the process.

• For detailed information on the Auto Volume function,

see the online help system.

Opti-source

279146 AM Rev.00 CCM-000922

Mute the zone outputs

• Select Out Gain for each zone.

• Click the Mute checkbox to silence the zone outputs of

the E4 system.

• Leave one zone active for monitoring purposes, or

connect a single speaker to the ZONE 1 output.

• When using sources that do not have an output gain

control, increase the input gain using the Gain slider

until the signal meter is solid green.

• Set Opti-source

to On. If you hear a dramatic

increase or decrease in volume, adjust your input gain

accordingly.

• NOTE: For detailed information on the setup of mic, line

and page sources see the online help system.

Adjust the zone EQ

• Select EQ for each zone.

• Make the desired adjustments to the Low, Mid and Hi

equalizer controls.

• Select Dynamic EQ for the zone and set it to On.

Flash hardware configuration

• Click the Flash Hardware Configuration button to

save the current system settings as the new default

configuration. The default configuration contains the

settings that are loaded when the E4 system is powered

on.

• Click the Save File button to save the settings in a file

on your PC where they can be stored for future use.

English

Opti-source