Maintaining Your Wave® SoundTouch™ Music System
Replacing the remote control battery
WARNING: Keep the remote control battery away from children. It
may cause a fire or chemical burn if mishandled. Do not recharge,
disassemble, heat above 212ºF (100ºC), or incinerate. Dispose of a
used battery promptly. Replace only with a battery of the correct type
and model number.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with an agency-approved (e.g. UL) CR2032 or
DL2032 3-volt lithium battery.
1.
Place the remote face down on a flat surface.
2.
Using your finger, push the tab lock to the side as shown and
hold. Slide the battery compartment open.
WARNING: Do not ingest battery, chemical burn hazard. The remote
control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed it can cause severe internal
burns in just two hours and can lead to death. Keep new and used
batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children.
If you think the battery may have been swallowed or placed inside any
part of the body seek immediate medical attention.
3.
Remove the old battery and install the new one with the plus
(+) symbol facing up.
4.
Gently slide the battery compartment closed. It locks
automatically.
26 - English
Alternate setup method
Using this method you can set up your Wave
music system by first joining its own built-in Wi-Fi
then connecting to your home Wi-Fi network.
Note: Use this method to set up your system as an AirPlay device,
only. To access the benefits of SoundTouch™, such as
streaming Internet radio and your music services, you must
add the system to your home Wi-Fi network using the
SoundTouch™ app (see page 9).
1.
On the Wave
SoundTouch™ music system remote, press the
®
Power button to turn on the system.
2.
On the back of the SoundTouch™ pedestal, press and
hold the Control button for about two seconds until
ALTERNATE SETUP is displayed on the front panel.
3.
On your smart device, activate Wi-Fi and join the Bose
SoundTouch™ Wi-Fi Network.
4.
Open a browser and type: http://192.168.1.1 in the address
field.
The Wi-Fi setup window appears on the screen.
5.
Select your home Wi-Fi network from the drop-down list.
6.
Enter your password (if required) and tap or click Connect.
The SoundTouch™ pedestal attempts to connect to your home
Wi-Fi network.
The Wi-Fi indicator on the rear panel of the SoundTouch™
pedestal momentarily blinks white and then turns solid white
when connected to the network.
7.
On your computer, tablet or smartphone, return to the Wi-Fi
control panel and rejoin your home Wi-Fi network.
8.
Once the system is on the network, follow these steps to
complete setup:
A. Download and launch the SoundTouch™ app. See
"Installing the SoundTouch™ app" on page 9.
B. On the SOUNDTOUCH™ SYSTEM SETUP screen, select
this option:
IT IS ALREADy ON my NETWORK
Disable/enable Wi-Fi capability
The SoundTouch
pedestal has built-in Wi-Fi capability that
TM
enables it to wirelessly connect to your home Wi-Fi network.
To disable Wi-Fi, press and hold the Control button on the back of
the SoundTouch
pedestal for at least eight seconds or until the
TM
Wi-Fi status indicator turns off.
To enable Wi-Fi again, turn on the system.
Power Saving mode
The SoundTouch
pedestal has a low-power standby mode in
™
which it consumes a minimum amount of power. This can be used
to reduce the power consumed in your home while you are away.
To place the SoundTouch
pedestal in the Power saving mode,
TM
press and hold the Control button on the back of the SoundTouch
pedestal for at least eight seconds or until the Wi-Fi status indicator
turns off. This also disables the Wi-Fi capability.
To wake up the SoundTouch
the Control button. The Wi-Fi capability is enabled again when any
source is selected.
SoundTouch™
®
network, and
®
pedestal, quickly press and release
TM
®
TM
페이지 인쇄