Bose Lifestyle 28 문제 해결 매뉴얼 - 페이지 2

{카테고리_이름} Bose Lifestyle 28에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bose Lifestyle 28 32 페이지. Dvd home entertainment systems
Bose Lifestyle 28에 대해서도 마찬가지입니다: 설치 매뉴얼 (32 페이지), 운영 매뉴얼 (44 페이지), 소유자 매뉴얼 (22 페이지), 운영 매뉴얼 (46 페이지), 운영 매뉴얼 (44 페이지), 운영 매뉴얼 (34 페이지)

Bose Lifestyle 28 문제 해결 매뉴얼
1. Parts that have special safety characteristics are identified by the symbol on
or by special notes on the parts list. Use only replacement parts that have critical characteristics
recommended by the manufacturer.
2. Make leakage current or resistance measurements to determine that exposed parts are accept-
ably insulated from the supply circuit before returning the unit to the customer. Use the following
checks to perform these measurements:
A. Leakage Current Hot Check-With the unit completely reassembled, plug the AC line cord
directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Refer to
UL6500 paragraph 9.1.1. Use a leakage current tester or a metering system that complies with
American National Standards Institute (ANSI) C101.1 "Leakage Current for Appliances" and
Underwriters Laboratories (UL) 6500, IEC 60065 paragraph 9.1.1. With the unit AC switch first in
the ON position and then in OFF position, measure from a known earth ground (metal waterpipe,
conduit, etc.) to all exposed metal parts of the unit (antennas, handle bracket, metal cabinet,
screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer
an electrical return path to the chassis. Any current measured must not exceed 0.5 milliamp.
Reverse the unit power cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT
WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT
MUST BE ELIMINATED BEFORE RETURNING THE UNIT TO THE CUSTOMER.
B. Insulation Resistance Test Cold Check-(1) Unplug the power supply and connect a jumper
wire between the two prongs of the plug. (2) Turn on the power switch of the unit. (3) Measure the
resistance with an ohmmeter between the jumpered AC plug and each exposed metallic cabinet
part on the unit. When testing 3 wire products, the resistance measured to the product enclosure
should be between 2 and infinite Meg ohms. Also, the resistance measured to exposed output/
input connectors should be between 4 and infinite Meg ohms. When testing 2 wire products, the
resistance measured to exposed output/input connectors should be between 4 and infinite Meg
ohms. If it is not within the limits specified, there is the possibility of a shock hazard, and the unit
must be repaired and rechecked before it is RETURNED TO THE CUSTOMER.
ELECTROSTATIC DISCHARGE SENSITIVE (ESDS)
This unit contains ESDS devices. We recommend the following precautions when repairing,
replacing or transporting ESDS devices:
• Perform work at an electrically grounded work station.
• Wear wrist straps that connect to the station or heel straps that connect to conductive floor mats.
• Avoid touching the leads or contacts of ESDS devices or PC boards even if properly grounded.
Handle boards by the edges only.
• Transport or store ESDS devices in ESD protective bags, bins, or totes. Do not insert unpro-
tected devices into materials such as plastic, polystyrene foam, clear plastic bags, bubble wrap or
plastic trays.
CAUTION: THE BOSE
VICEABLE PARTS. TO PREVENT WARRANTY INFRACTIONS, REFER SERVICING TO
WARRANTY SERVICE STATIONS OR FACTORY SERVICE.

SAFETY INFORMATION

DEVICE HANDLING
®
PS 28 AND PS 35 POWERED SPEAKER CONTAINS NO USER-SER-
PS18/28/35 Troubleshooting Guide
2
schematics