3M XT-1 매뉴얼 - 페이지 6

{카테고리_이름} 3M XT-1에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3M XT-1 8 페이지. Drive-thru systems
3M XT-1에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (6 페이지), 빠른 참조 매뉴얼 (2 페이지), 기술 게시판 (10 페이지), 기술 데이터 (2 페이지), 기술 게시판 (2 페이지), 빠른 시작 매뉴얼 (3 페이지)

페이지 인쇄

Change Basic Volume Settings

Note: All volume settings should be adjusted during normal or peak business hours. Adjusting them during

slow times will likely produce volume settings that are too low.

Note: Inbound and outbound are always defined from the perspective of the headset.

Inbound Microphone Volume

Changing the inbound microphone volume affects the sound volume coming from the customer order

point microphone. To turn up or down the inbound microphone:

1. Enter the configuration mode.

2. Select a new value for 01 Drivethru Volume > Inbound Mic Volume. The range is 0 (silent) to

20 (maximum).

Outbound Talk Volume

Changing the outbound talk volume affects the volume of the speaker at the customer order point.

Note: To avoid feedback, set the outbound talk volume as low as possible.

To change the outbound talk volume:

1. Enter the configuration mode.

2. Select a new value for 01 Drivethru Volume > Outbound Talk Volume. The range is 0 (silent) to

20 (maximum).

Vehicle Alert Volume

Changing the vehicle alert volume affects the volume of the vehicle alert signal on the headsets.

To change the vehicle alert volume:

1. Enter the configuration mode.

2. Select a new value for 01 Drivethru Volume > Vehicle Alert Volume. The range is 0 (silent) to

20 (maximum).

Outbound Greeter Message Volume

Changing the outbound greeter message volume affects the sound volume of the custom greeting

messages and the system internal greetings ("Store Closed" and "Please Pull Ahead"). To turn up or

down the greeter message volume:

1. Enter the configuration mode.

2. Select a new value for 01 Drivethru Volume > Greeter Message Volume. The range is 0 (silent) to

20 (maximum).

Change the Monitor Volume

The monitor is an additional speaker that can be used to monitor drive-thru communication without a

headset, typically in the kitchen. If the monitor has a volume control built into it, you can use it to control

the overall volume level of the speaker. To be more specific about which elements you want to control,

follow the instructions below.

Inbound Listen

Changing the inbound listen volume affects how loudly the monitor plays the inbound (customer

order point) communication. You can also disable the monitor playing inbound sounds. To change

the inbound listen monitoring settings:

1. Enter the configuration mode.

2. Select 02 Monitor Volume.

3. To enable or disable the monitor playing the inbound sounds, change the value for

Inbound Listen: Enable to ON or OFF.

4. To change the volume level, select a new value for Inbound Listen: Volume. The range is 0 (silent) to

20 (maximum).

Night Volume

You can assign a standard reduction in the volume level of the customer order point speaker for night hours

when lower volume is typically required. With the night volume set, the system automatically adjusts the

volume during night hours, then back to normal during the day. To change the night volume setting:

1. Enter the configuration mode.

2. Select a new value for 03 Night Volume > Reduce Drive-Thru Volume At Night By. The range is

0 (silent) to the current day volume level (maximum).

Note: Night Volume is never higher than Day Volume. Night volume reduction is a subtracted value, not the

resulting level; therefore, if it is the same as the day volume level, the speaker will turn off at night. You cannot

change the day outbound talk volume on this screen, only the reduction amount identified above.