Anolis ArcWash Recessed 136 RGB 사용자 설명서 - 페이지 13

{카테고리_이름} Anolis ArcWash Recessed 136 RGB에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Anolis ArcWash Recessed 136 RGB 19 페이지. Rgb

페이지 인쇄

DM.Pr. --- DMX preset.Select this item to choose desired DMX mode.Please refer to the chapter "DMX protocol" for

detail description.

Mi.SE. --- Microphone sensitivity.Select this function to adjust the microphone sensitivity from 1(maximum) to

20(minimum).If the sensitivity is correctly adjusted,the upper segment of the first digit blinks in the bass beat.

Examples:

underexited

FEEd --- Pan/Tilt feedback.This function allows to return the mowing head to the required pan/tilt position after changing

the position by external force (e.g.by stroke).

Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the fixture can be de-

maged!

Note: If the feedback was switched off ,the pan/tilt-position is changed by an external force and the feedback is switched

on again,the moving head might not to be synchronized with the DMX signal.You have to make a reset in order to syn-

chronize the moving head with the DMX signal.

P.t.Mo. --- Pan/tilt movement mode.Use this menu to set the character of the pan/tilt movement.

ti.Mo. --- Time mode.Pan and tilt will move with different speeds and they will come at the same

time to end point (pan and tilt sets its optimal speed).

SP.Mo. --- Speed mode.Pan and tilt will move with the same speed as adjusted at the channel 5

(Pan/Tilt speed).E.g. pan will come to the end point and wait for tilt,which has longer track.

bL.Co. --- Blackout during movement correction.Select this function to enable the blackout during the head movement

correction (if the moving head lost its right pan/tilt position for a short moment).

bl.P.t. --- Active Blackout while Pan/Tilt moving: - Use this function if you wish to close the light output during

pan/tilt changes.

bALA. --- Balance.Select this function to enable (On) or disable (OFF) the white balance which is set in "White colour

balance" menu below.If this function is set OFF,ArcWash 136 RGB will use maximum values (255) of saturation for red,

green and blue channel.

C.bAL. --- White colour balance. Using this menu you can set the white balance:

1. Browse through the menu by pressing the [UP] and [DOWN] buttons until the display shows "C.bAL." menu.Press

[ENTER] button and "rEd.b." will appear on the display.

2.Press [ENTER] button again and use [UP] and [DOWN] buttons to adjust the new maximum value required for the red

channel.Confirm your choice by pressing [ENTER].Use the [UP] and [Down] buttons to select next colour.

3.Repeat step 2 for green channel "GrE.b." and for blue channel "bLu.b".

i.bLi. --- Initial blink.If this function is on,ArcWash 136 RGB makes auto-calibration (All LEDs light on 100% for a short

time) after switching the fixture on.If this function is set off,you have to set manually every colour on max.brightness after

switching on the driver before starting regular operating.This action should last min. one second for every colour.

dF.SE. --- Default Settings .Select this option to reset all fixture personalities to the factory values.

7.4 Manual mode

Select this menu to control channel effects by control buttoms on the control board without an external controller.

PAn

a coarse pan movement

F.PAn

a fine pan movement

tilt

a coarse tilt movement

F.tilt

a fine tilt movement

SpEd

a pan/tilt speed

P.t.SE. a pan/tilt macro selection

P.t.SP. a pan/tilt speed

Func.

a special function

rED

a red LED saturation

right level

(upper segment blinks)

overexited

GrEE

a green LED saturation

bLuE

a blue LED saturation

MACr

a colour macros

Stro.

a strobe,shutter

dimr

a dimmer