Daikin R32 Split Series 설치 매뉴얼 - 페이지 8

{카테고리_이름} Daikin R32 Split Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Daikin R32 Split Series 16 페이지. R32 split series
Daikin R32 Split Series에 대해서도 마찬가지입니다: 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (14 페이지), 운영 매뉴얼 (16 페이지), 운영 매뉴얼 (16 페이지), 운영 매뉴얼 (8 페이지), 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (13 페이지)

페이지 인쇄

Indoor Unit Installation

3-2. Left-side, left-back, or left-bottom piping

How to switch around the drain plug and drain hose

1) Remove the ﬁxing screw and

pull out the drain hose.

1 Remove ﬁxing

1) Switch around the drain plug and drain hose.

2) Attach the drain hose to the underside of the refrigerant

pipes with adhesive vinyl tape.

3) Shape the refrigerant pipes along the pipe path marking

on the

4) Pass the drain hose and refrigerant pipes through the

wall hole, then position the indoor unit on the

plate hooks, using the

unit as a guide.

5) Open the front panel, then open the service lid. (Refer to

"Service lid" on page 4.)

6) Pass the inter-unit wire from the outdoor unit through the

feed-through wall hole and then through the back of the

indoor unit. Pull them through the front side. Bend the ends

of tie wires upward for easier work in advance.

(If the inter-unit wire ends are to be stripped first, bundle

wire ends with adhesive tape.)

7) Connect the refrigerant pipes.

8) In case of pulling the drain hose through the back of the

indoor unit, wrap the refrigerant pipes and drain hose

together with

9) Press the bottom frame of the indoor unit with both hands

until it is firmly caught by the

Make sure that the wires do not catch on the edge of the

indoor unit.

3-3. Wall embedded piping

Follow the instructions given under left-side, left-back, or

left-bottom piping.

1) Insert the drain hose to a depth of 1-15/16 inches (50mm)

or more so it will not be pulled out of the drain pipe.

3) Switch around the drain hose and drain plug.

Drain plug

screw.

Drain hose

Pull out

drain hose.

Insert a hexagonal

2) Pull out

wrench (3/16 inch (4mm)).

drain plug.

mounting plate.

markings at the top of the indoor

insulation tape as shown in the figure.

mounting plate hooks.

Push the drain plug all the

way in using a hexagonal

wrench (3/16 inch (4mm)).

Hexagonal wrench

(3/16 inch (4mm))

Do not apply lubricating oil

(refrigerant oil) to the drain

plug when inserting it.

The application of lubrication

oil to the drain plug will

deteriorate the plug to cause

drain leakage from the plug.

Remove pipe port cover here for

left-bottom piping.

mounting

Drain

hose

Caulk this

hole with

putty or

caulking

material.

Drain hose

(Be sure the drain

hose is lower)

Bottom frame

Wrap with vinyl tape so that no gap is left and the slit in the

thermal insulation pipe is facing upward.

Thermal insulation pipe

Insert the drain hose

to this depth so it will

not be pulled out of

the drain pipe.

Insert drain hose securely

and ﬁx in place with ﬁxing

screw.

Fixing screw

Drain hose

Left-bottom piping

Bind with adhesive vinyl

Wrap

tape.

around the bent portion

If any gap is left or if the

of refrigerant pipe.

refrigerant pipe is bound

Overlap at least half the

too tightly, condensation

width of the tape with

and dripping may result.

each turn.

Mounting plate

Refrigerant pipes

Secure the indoor unit to the

mounting plate with the

indoor unit ﬁxing screws

M4 × 1/2" (M4 × 12mm)(2 points).

Slit

Inner wall

1-15/16"

Drain hose

(50mm)

or more

Vinyl chloride

drain pipe (VP-30)

Outer wall

φ1-3/16" (30mm) or more

Remove pipe port

cover here for

left-side piping.

Left-side piping

Left-back piping

A Mounting

plate

insulation tape

Vinyl tape

■

English