DS Greenhouse Blast GH450 소유자 매뉴얼 - 페이지 2

{카테고리_이름} DS Greenhouse Blast GH450에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DS Greenhouse Blast GH450 13 페이지. High efficiency wood or coal furnace

페이지 인쇄

ALL D.S. Furnaces must be installed by a NFI Certified Technician

Safety Instructions

1. Read all instructions before installing or operating any DS furnace

2. You must install smoke and carbon monoxide detectors before you install or operate any furnace. Check

your local codes, this installation must meet their rulings.

3. Do not open bottom ash door to increase draft. It is designed only to empty ash pan.

4. Never leave furnace doors open when furnace is unattended.

5. Install barometric or manual damper when burning coal.

6. Do not use a manual, barometric or automatic damper when burning wood.

7. Do not hook up a wood or coal furnace to an aluminum Type B gas vent. Use a code approved Class A

chimney. A minimum of 20' high.

8. On all new installs connecting to an existing chimney, a level 2 chimney inspection must be done by a

Certified Chimney Sweep.

9. Clean chimney before installing furnace. If there is creosote attached to the liner you could create a seri-

ous chimney fire.

10. Never leave children unsupervised when they are in same room as furnace. Provide a sturdy barrier to

keep children and pets a safe distance from the furnace, or they could get burned.

11. Keep Furnace area clear from all combustible materials, gasoline, and other flammable vapors and liquids.

12. Furnace must be installed on a noncombustible floor.

13. Check the clearance to combustible walls and floors on page 4.

14. Do not allow anyone who is unfamiliar with furnace to operate it.

15. Spend some time with your furnace to become well acquainted with the different settings and how each

setting will affect its burning patterns. It is impossible to state how each setting will affect your furnace.

16. Be extremely careful when removing the furnace ash pan. It may be very hot!

17. Make sure your single wall chimney connectors have at least 3 screws per joint.

18. Do not install this furnace in a mobile home or trailer.

Operational / Work Practice Standards

1. When burning wood, burn only seasoned, dry cord-wood that has been dried; then warmed before firing.

(Warming cord-wood means placing in a heated building for 1 day before burning)

2. Keep wood under cover: in a wood shed, or a tarp.

3. Right after delivery: stack cord-wood under cover

4. Split cord wood before drying.

5. Do not burn green wood, it needs to have no more than 20% moisture.

6. All firewood must be seasoned at least 1 year.

7. Check cord-wood with moisture meter. Check wood moisture at least once a week!

8. Keep a 2" to 3" ash layer on top of your grates when burning wood. Note: Do not cover louvers.

9. The furnace is designed to burn air dried wood and coal at a predetermined firing rate. Over firing occurs

when the ash door is left open during operation or a highly volatile fuel, i.e. large amounts of small kindling is

used. Do not exceed 600 degrees on top of furnace.

10. When tending the firebox always open load door slowly to minimize smoke out the fire door or to avoid a

"flash back".

11. Check the fit on the load door. It must fit tightly. If it does not, check for deterioration or wear of the ce-

ramic rope seal. Replace defective seals.

12. Inspect and clean your chimney and single wall chimney connectors regularly.

13. In the event of a chimney fire, shut all draft controls and blower off and call your fire department immedi-

ately. Alert everyone in the house. If flue is still burning vigorously, throw baking soda into firebox or discharge a

fire extinguisher into fire box. After the chimney fire is over, have a certified chimney sweep complete a level 2

chimney inspection, before farther use of your chimney.

14. Equip your building with fire extinguishers, carbon monoxide and smoke detectors.

15. Do not burn garage, gasoline or any other flammable liquids in this furnace.

16. This is a wood and coal-burning furnace and should not be altered in any way.

17. Do not burn furnace over 600 degrees or warranty will be void!