DSC PC56O 사용 설명서 - 페이지 12

{카테고리_이름} DSC PC56O에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC PC56O 16 페이지.

페이지 인쇄

CHANGING SYSTEM FEATURES

Changing Access Codes

The PC560 features 4 programmable Access Codes. The first code is the Master Code, and the remaining

three codes are normal Access Codes.

Programming Access Codes: Enter [

FLASH. The Zone Lights will indicate which Access Codes have been programmed, and which Access

Code is presently being programmed:

∗

When the [

][5][Master Code] command is entered, Zone Light 1 will be ON to indicate that the Master

Code is already programmed.

Changing or Adding a Code: To change the Master Code or Access Codes 2 through 4, enter the number

of the code to be changed; the corresponding Zone Light will begin to FLASH. For example, enter [1] to

change the Master Code, or enter [2] to change Access Code 2, and so on.

With the desired Zone Light flashing, enter a new 4-digit Access Code. Do not press [

entering the code. If an existing code is being changed, the new code will replace the old one. After the

code is entered, the keypad will beep 3 times and the Zone Light will stop flashing and remain ON.

If you want to program another code, press the number key for the code to be programmed, and enter the

new 4-digit code as described above. When all desired changes are complete, press the [#] Key to return

to "Ready".

Erasing a Code: To erase a code, enter [

the Zone Light for the code will FLASH. Enter [

changes are complete, press the [#] Key to return to "Ready".

IMPORTANT: Do not erase the Master Code. If the Master Code is accidentally erased, contact your

installing company for assistance.

Door Chime On/Off

The Door Chime feature causes the keypad to beep whenever an Entry-Exit Zone or Instant Zone is

activated. This feature is useful if the Entry-Exit door or doors are out of view, and you would like an

indication of when the door zones are opened and closed. Note that the Door Chime feature only functions

when the system is disarmed.

To turn the Door Chime feature ON or OFF, enter [

sounder will beep 3 times. If the feature is being turned OFF, the sounder will emit a single long tone.

Adjusting the Keypad Sounder Tone and Backlighting

The sounder tone and the lighting behind the keys for each Keypad may be individually adjusted. The sounder

tone may be set with a loud tone, a softer tone, or no tone at all. The backlighting can be set at medium or high

brightness, or it may be turned off.

To adjust the Keypad's sounder, press and hold the [#] Key; after two seconds, the sounder will begin to beep.

With each beep, the tone of the beep will increase or decrease. When the desired tone is achieved, release

the [#] Key.

To adjust the Keypad's backlighting, press and hold the [

and the Keypad will beep as each of the three backlighting levels is shown: medium, high and off. When the

desired level is reached, release the [

If all power to the system is shut off, each Keypad's tone and backlighting will be restored to the factory settings.

∗

][5][Master Code]; the "Ready", "Armed" and "System" lights will

Zone Light

OFF

ON steady

Flashing

∗

][5][Master Code]. Enter the number of the code to be erased;

∗∗∗∗

∗

] Key. Press the [#] Key to return to the "Ready" mode.

Access Code is...

not programmed

programmed

presently being programmed

] to erase the Access Code. When all desired

][6]. If the feature is being turned ON, the keypad

∗

] Key. The zone and status lights will be shut off,

∗

] or [#] when