DSC PK5500 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} DSC PK5500에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC PK5500 16 페이지. Power series
DSC PK5500에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 설치 지침 매뉴얼 (9 페이지), 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

Programming the Keypad

There are several programming

Toggle Option

options available for the key-

pad. These are described below.

1 _ _ 4 _ _ _ _

Programming the keypad is

similar to programming the rest of the system. When you are in the keypad

programming sections, the keypad will display which options are turned on

along the bottom of the display. To turn an option on or off, press the

number corresponding to the option on the number pad. The numbers of

the options that are currently turned ON will be displayed. For example, if

options 1 and 4 are on, the display will look like diagram shown on the

different keypad displays.

For information on programming the rest of your security system, please

refer to your system's Installation Manual.

Broadcasting LCD Labels

All LCD programming is done per keypad. If more than one LCD keypad is

present on the system, labels programmed at one keypad can be broadcast

to all other LCD keypads. Perform the following procedure in order to

broadcast labels:

Step 1 - Program one LCD keypad completely.

Step 2 - Make sure all LCD keypads are connected to the Keybus.

Step 3 - Enter keypad programming by pressing [,][8][Installer

Code][,], then enter section [998] at the keypad that was programmed.

The keypad will now broadcast all the information programmed to all the

other LCD keypads on the system.

Step 4 - When the keypad is finished press the [#] key to exit.

NOTE: LCD Label broadcast from this keypad is only compati-

ble with PC1616/1832/1864 control panels and other

PK5500 keypads.

Language Programming

Hold the [<][>] keys for 2 seconds to enter language programming,

scroll to the desired language and Press [,] to select.

NOTE: If section [077] option 4 is OFF, language programming

can only be performed while in installers programming.

Enrolling the Keypad

The keypad will need to be assigned to a partition and slot if supervision or

keypad zones are being used. Keypad assignments and keypad option

programming must be done at each keypad individually.

The 1st digit of keypad assignment is used to determine partition assign-

ment (1 to 8). If partitioning is not used, enter [1]. For Global Keypads,

enter [0].

The 2nd digit of keypad assignment is used to determine slot assignment

for keypad supervision. Each keypad will be assigned a different slot num-

ber from 1 to 8. PK5500 LCD keypads come defaulted in slot 8. If multi-

ple LCD keypads are used one LCD keypad must remain in slot 8.

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [,][8][Installer's Code].

2. Press [000] for Keypad Programming.

3. Press [0] for Partition and Slot Assignment.

4. Enter the 1st digit (0 to 8 for partition assignment).

5. Enter the 2nd digit (1 to 8 for slot assignment supervision).

6. Press the [#] key twice to exit programming.

7. After assigning all keypads, perform a supervisory reset by entering

[,][8][Installer's Code][902] and wait for 60 seconds.

8. Press the [#] key to exit programming.

Programming Labels

1. Enter keypad programming by pressing [,][8][Installer Code][,].

Enter the 3-digit section number for the label to be programmed.

2. Use the arrow keys [<][>] to move the underline bar underneath the

letter to be changed.

Press the number keys [1] to [9] corresponding to the letter you require.

The first time you press the number the first letter will appear. Pressing

the number key again will display the next letter, etc

NOTE: To select lower case letters press [*], scroll to "lower case"

and press [*] again to select.

[1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space

[2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8

[3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0

4. When the required letter or number is displayed use the arrow keys

[<][>] to scroll to the next letter.

5. When you are finished programming the Zone Label, press the [,] key,

use the [<][>] keys to scroll to "Save" then press [,].

6. Continue from Step 2 until all labels are programmed.

Entering ASCII Characters

To enter ASCII characters, press

[,]

, scroll to "ASCII Entry" then press

to select. Enter the corresponding three-digit number and press

[,]

[,] to save and exit.

Changing Brightness/Contrast

1. Press [,][6][Master code].

2. Use the [<][>] keys to scroll to either Brightness Control or Contrast

Control.

3. Press [,] to select the setting you want to adjust.

4. a) 'Bright Control": There are multiple backlighting levels. Use the

[<][>] keys to scroll to the desired level.

b) 'Contrast Control": There are 10 different display contrast levels. Use

the [<][>] keys to scroll to the desired contrast level.

5. To exit, press [#].

Changing the Buzzer Level

1. Press [,][6][Master Code].

2. Use the [<][>] keys to scroll to Buzzer Control.

3. There are 21 different levels, use the [<][>] keys to scroll to the

desired level.

4. To exit, press [#].

Emergency Keys

Press the (

Press both (

Panic transmission.

Broadcasting Door Chime

All door chime programming is done per keypad. If more than one key-

pad is present on the system, door chime programmed at one keypad

can be broadcast to all other keypads. Perform the following procedure

in order to broadcast door chime:

Step 1 - Program one keypad completely.

Step 2 - Make sure all keypads are connected to the Keybus.

Step 3 - Enter keypad programming by pressing [,][8][Installer

Code][,], then enter section [994] at the keypad that was programmed.

The keypad will now broadcast all the door chime information programmed

to all the other keypads on the system.

Step 4 - When the keypad is finished press the [#] key to exit.

Hereby, DSC, declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

The complete R&TTE Declaration of Conformity can be found at http://

www.dsc.com/listings_index.aspx.

EN50131-1 Grade 2, Class II

Operating Instructions shall be made available to the user.

) key for 2 seconds to send a Fire transmission.

) keys simultaneously for 2 seconds to send a