DSC PG9944 설치 지침

{카테고리_이름} DSC PG9944에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC PG9944 2 페이지. Wireless outdoor pir detector with camera

페이지 인쇄

PG9944/8944/4944 Installation

Instructions

W ireless Out door PIR Det ect or wit h Camera

Overview

The PGx944 uses eight PIR sensors, each acting as a

Quad detector to accurately and reliably determine

whether an alarm is justified. Features & benefits

include:

Optimum performance even in poor weather con-

ditions such as snow, rain, dust, wind and direct

sunlight.

Tamper protection prevents opening and removal

from wall.

Built-in link quality indicators reduce installation

time by eliminating the need for the installer to

physically approach the control panel.

Microprocessor-controlled compensation.

Immunity to pets weighing up to 18 Kg (40lb).

NOTE: Pet immunity feature has not been evaluated

to UL 639 or ULC-S306- 03 due to the feature not

being addressed in either standard.

CAMERA FEATURES

Color or black & white images

Auto-setup for brightness and contrast via the con-

trol panel

Day and night CMOS camera, with IR illumination.

This allows taking pictures in full darkness

Camera range of 12m (40ft); with IR illumination

10m (33ft)

Camera operation modes:

Post alarm – pictures are taken after detec-

tion by detector.

Visual Verification

Device Setup

WARNING! To comply with FCC and IC RF exposure

compliance requirements, the PIR detector should be

located at a distance of at least 20 cm from all persons

during normal operation. The antennas used for this

product must not be co-located or operated in con-

junction with any other antenna or transmitter.

NOTE: The PG Series wireless PIR Motion detectors

shall be installed and used within an environment that

provides the pollution degree max 2 and overvoltages

category II in NON HAZARDOUS LOCATIONS.

The equipment is designed to be installed only by qual-

ified service persons.

NOTE: To ensure the continued operation of all wire-

less devices after performing a system default, a

global upload of all wireless programming via DLS is

recommended before defaulting the system. After

completing the system default, download the wireless

programming.

NOTE: Back tamper switch is required for UL com-

mercial burglary installations.

BATTERY INSTALLATION

Initial battery installation should be done on a flat sur-

face. After inserting the batteries, the LED flashes for

60 seconds and the detector enters a 15 minute local

diagnostic mode.

NOTE: When manually programming wireless

devices, if a device has been powered up for more

than 48 hours it cannot be enrolled into the system

until the device has been tampered and restored.

When programming the panel using Quick Enroll, fol-

low the steps detailed in "Enrollment."

NOTE: After restoring a low battery trouble the sys-

tem may take up to 5 minutes to clear the trouble.

ENROLLMENT

To quick enroll:

On a keypad press [*] [8] [Installer Code] [804]

[000].

Press and hold the device enroll button until the

LED lights steady and then release the enroll but-

ton while the LED is still lit. A confirmation mes-

sage then appears on the keypad.

Press [*] key to confirm ID.

Enter [3 digit zone #].

Enter [3 digit zone type].

Enter [1 digit partition #] for all desired partitions

and press [#]. If using an LCD keypad you can

scroll to the desired partitions and press [*] to

toggle the partition.

On an LCD keypad enter the label by using word

library.

To pre-enroll:

Remotely configure the unique ID number into the

system. For more information see the HSM2HOST

manual.

When on-site, press the device enroll button.

NOTE: If the wireless device has been powered for

more than 48 hours without being enrolled, tamper

and restore the device to enroll it.

PLACEMENT AND WALK TESTING

Before permanently mounting any wireless device,

temporarily mount the device and perform a Place-

ment test. Perform a walk test of the coverage area at

least once a year to ensure that the detector is work-

ing correctly.

Tamper the device by removing the cover.

Restore the tamper. The device

now enters Placement test

mode for 15 minutes.

Trip the device and the red

LED blinks once to identify

that a signal is being sent to the

receiver and then blinks three

times to identify the signal

strength. To perform a walk

test, walk across the far end of

coverage pattern in both dir-

ections. The following table indicates received sig-

nal strength indication.

LED Response

Signal Strength

Green LED blinks

STRONG

Orange LED blinks

GOOD

Red LED blinks

POOR

No blinks

No communication

IMPORTANT! Only GOOD or STRONG signal

strengths are acceptable. If you receive a POOR sig-

nal from the device, re-locate it and re- test until a

GOOD or STRONG signal is received.

NOTE: For UL/ULC installations, only STRONG sig-

nal levels are acceptable. After installation verify the

product functionality in conjunction with the com-

patible receivers HSM2HOST9, HS2LCDRF(P) 9,

HS2ICNRF(P) 9 and PG9920.

NOTE: For detailed Placement instructions refer to

the control panel Reference Manual.

MOUNTING THE DEVICE

Installation Notes: The top cover should only be

accessed by authorized service personnel or man-

ufacturer. Do not obscure the detector field of view

with large objects. Install in position such that expec-

ted intruder motion is perpendicular to the zones of

detection.

Alarms triggered by conditions such as weather, blow-

ing leaves and brush, or related environmental con-

ditions, etc., need to be considered when assessing the

installation and application. If nuisance trips are not

tolerable it is recommended that the wireless outdoor

intrusion detection unit is enrolled in the system to a

zone that is defined as a trouble alarm circuit.

Fix the bracket firmly on a stable wall or pillar.

The orientation of the fixed bracket must be as par-

allel as possible to the surveyed ground surface.

Mark drilling point

Drill

Fasten with three long screws

Fasten the detector to the bracket with two short

screws.

Adjust the detector's horizontal and

vertical angles according to the

surveyed ground surface. The ver-

tical angle indicator position for

various installation height and cov-

erage distance combinations is

detailed in the following table (the

information refers to a relatively

flat surveyed area. Verify the ver-

tical adjustment by walk-test).

Coverage Distance

Mounting Height

10m

12m

6.7 ft

13 ft

20 ft

26 ft

33 ft

39 ft

3.0m/ 10 ft

2.5m/ 8 ft

2.0m/ 7 ft

1.5m/ 5 ft

LED Operation

LED Indications

Event

Red LED blinks

Stabilization (warm-up 60 sec.)

Red LED on 0.2

Tamper open/close

sec.

One quad PIR detection in dia-

Red LED 2 blinks

gnostic mode

Red LED on 2 sec.

Intruder alarm

Configuration

To enter the wireless configuration section enter

[804][Zone Number].

DEVICE TOGGLE

[001][01]

Alarm LED - Default [Y]

Enables the devices LED to

activate when an alarm event

occurs.

[001][04]

Supervision - Default [Y]

Enables supervision of the

device.

[001][09]

More Options

[03] 24Hr/Night - Default [Y]

Define if motion alarms are

always enabled or only

enabled at night. For UL/ULC

installations night mode is to

used to supplement the pro-

tection covering the detec-

tion area.

DEVICE OPTIONS

[003]

Hightraffic Shutdown - Default [01]

Activating this feature helps conserve battery

power when the system is disarmed by con-

figuring a reporting timer. When motion is

detected, the device transmits an alarm to the

receiver and will not report any further events

until the timer expires. Any motion detected

during the configured period will be reported

once the timer expires. No Delay causes the

device to report an alarm each time the

detector is tripped.

[01] Detector

Disabled

[03] 5 second

[02] No Delay

(while dis-

delay

armed)

[04] 15

[05] 30

[06] 1m delay

second delay

[08] 10m

[07] 5m delay

[09] 20m delay

delay

[10] 60m

delay

[004]

Image Brightness - Default [04]

Lightens and darkens the image

[01] Image

[02] Image

[03] Image

Bright

-3

-2

-1

[04] Image

[05] Image

[06] Image

Bright

[07] Image

Bright

[005]

Image Contrast - Default [04]

Lightens and darkens the contrast.

[01] Image

[02] Image

[03] Image

Contrast

-3

-2

-1

[04] Image

[05] Image

[06] Image

Contrast

[07] Image

Contrast

[007]

Detection Sensitivity - Default [02]

Selects the sensitivity range of PIR devices.

[01] Low Sens-

[02] Mid Sens-

[03] High

itivity

Sensitivity

[04] UL Stand-

ard

[011]

Camera Toggles

[03] Normal

[01] Color -

[02] High Res.

Res. - Default

Default [Y]

- Default [Y]

[N]

[09][01] AC

[09] More

Power -

Options

Default [N]

SPECIFICATIONS

Caution! Risk of explosion if battery is replaced by

an incorrect type. Dispose of used batteries according

to the manufacturer's instructions and according to

local rules and regulations. Batteries are to be

replaced by service persons only.

OPTICAL

Black Mirror Max. Coverage: At least 12 m (40 ft) /

90°

Detector Technology: 8 independent quad PIR detect-

ors operating in true Quad configuration

Pet Immunity: Up to 18 Kg (40 lb)

ELECTRICAL

Input Power: Two 3V CR17450 Lithium batteries

Note: For UL installations use Eve Energy Co. CR17450 only.

Battery Life (for typical use): minimum one year, typ-

ical 3 years (not verified by UL/ULC)

Low Battery Threshold: 4.0 V

Functional

Picture Resolution: 320x240 pixels QVGA

Frame Rate: up to 2 fps (for user)

Alarm period: 2 seconds

WIRELESS

Frequency Band (MHz): CE Listed PG4944:

433MHz; CE/EN listed PG8944: 868MHz;

FCC/IC/UL/ULC listed PG9944: 912- 919MHz

MOUNTING

Mounting type: Wall mounting

Mounting Height: 1.5 – 3.0 m (5 – 10 ft). Must be 8

feet for UL/ULC listed installations.

Horizontal Adjustment: -45° to +45°, in 5° steps

Vertical Adjustment: 0° to -10°, in 2.5° steps

ENVIRONMENTAL

Temperature range: - 40ºC to +70ºC (UL/ULC only

verified the range - 35ºC to +66ºC)

Relative Humidity: up to max. 93%RH, non- con-

densing

White Light Immunity: Above 25000 lux

PHYSICAL

Size (H x L x W): 157 x 147 x 124 mm (6- 3/16 x 5-

13/16 x 4- 7/8")

Weight (with battery): 600 g (21 oz)

COMPATIBLE RECEIVERS

433MHz Band: HSM2HOST4; HS2LCDRF(P)

4;HS2ICNRF(P)4; PG4920

868MHz Band: HSM2HOST8; HS2LCDRF(P)8;

HS2ICNRF(P) 8;PG8920

912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9;

HS2ICNRF(P) 9; PG9920

NOTE: Only devices operating in band 912- 919MHz

are UL/ULC listed.

Notice

The PGx944 detector was designed to adhere to

applicable privacy regulations and only processes

data needed for the primary functionality of the

device. Before using the detector you will be asked to

provide consent with processing of the personal data

that the detector may capture. Note that the detector

records video to secure the best functionality of the

device. The recordings are processed securely and

automatically erased on a periodic basis. Based on the

location of the module you may have the obligation to

issue a notice about using it.

The data recorded through the PGx944 detector are

processed and maintained primarily by the data con-

troller. Data controller is the entity that provides mon-

itoring services to you. You have the right to enquire

about your data with them. For more information

about their privacy practices please contact the data

controller.

For more information about Tyco privacy practices

please visit our website http://www.tyco.com/privacy.

UL/ULC Not e s

Only model PG9944 operating in the frequency band 912-919MHz is

UL/ULC listed. The PG9944 has been listed by UL for commercial and

residential burglary applications and by ULC for residential burg-