DSC PG9974(P) 설치 지침 매뉴얼

{카테고리_이름} DSC PG9974(P)에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC PG9974(P) 6 페이지. Wireless powerg high-security mirror detector with anti-masking

페이지 인쇄

D-304674

PG9974(P)/PG8974(P)/PG4974(P)

Wireless PowerG High-security Mirror Detector

with Anti-masking Installation Instructions

Features

The PGx974(P) (pet-immune) are 2-way, microprocessor-con-

trolled, wireless digital mirror PIR detectors which include the

following features:

• Built-in link quality indicators reduce installation time by

eliminating the need for the installer to physically approach

the control panel.

• Adaptive Active Infra-Red Anti-Masking technology

providing the most advanced reliable protection against

intentional masking attempts (patent pending).

• Includes a fully supervised PowerG transceiver.

• Incorporates patent pending black mirrors for extremely

high white light immunity.

• Advanced elliptical / parabolic mirror technology

(patented).

• V-slot® optic technology (patented) for improved

robustness, anti-vandalism and for very high reliability.

• Creep zone protection.

• PGx974P can distinguish between human beings and pets

weighing up to 18 kg (40 lb).

• The advanced True Motion Recognition™ algorithm

(patented) distinguishes between the true motion of an

intruder and any other disturbances which may cause false

alarms.

• No vertical adjustment is needed.

• Motion event counter determines whether 1 or 2

consecutive motion events will trigger an alarm.

• Automatic termination of walk-test after 15 minutes.

• Microprocessor-controlled temperature compensation.

• Sealed chamber protects the optical system.

• Front and back tamper protection.

• Self-test.

Device Setup

Note: To ensure the continued operation of all wireless devices

after performing a system default, a global upload of all wire-

less programming via DLS is recommended before defaulting

the system. After completing the system default, download the

wireless programming.

Legend

A. Screw cover

B. LED

C. PIR optical window

D. Enroll button (use a screwdriver to press the recessed but-

ton)

E. Battery

Tamper switch

G. Break-away base segment (shaded)

H. Mounting height

Coverage range

Horizontal view

K. Vertical view

X. Lower surface (with downward tilt)

Y. Upper surface (without downward tilt)

Installing the Battery

Caution! Risk of explosion if battery is replaced by an incor-

rect type. Dispose of used batteries according to the manufac-

turer's instructions and according to local rules and regulations.

Batteries are to be replaced by service persons only.

1. On the indicated location, lift the screw cover upward using

your thumb.

2. Release the screw and open the cover in the direction shown

by the arrow.

3. Insert a screwdriver into the slot and then push inward to sep-

arate the base from the cover.

4. Insert battery while observing polarity.

Note: When manually programming wireless devices, if a

device has been powered up for more than 48 hours it cannot be

enrolled into the system until the device has been tampered and

restored. When programming the panel using the Quick Enroll

procedure follow the steps detailed in Enroll the Device into the

System.

Note: After restoring a low battery trouble the system may take

up to 5 minutes to clear the trouble.

Enroll the Device into the System

To quick enroll:

1. On a keypad press [*] [8] [Installer Code] [804] [000].

2. Press and hold the device enroll button until the LED lights

steady and then release the enroll button while the LED is

still lit. A confirmation message then appears on the keypad.

3. Press [*] key to confirm ID.

4. Enter [3 digit zone #].

5. Enter [3 digit zone type].

6. Enter [1 digit partition #] for all desired partitions and press

[#]. If using an LCD keypad you can scroll to the desired par-

titions and press [*] to toggle the partition.

7. On an LCD keypad enter the label by using word library.

To pre-enroll:

1. Remotely configure the unique ID number into the system.

For more information see the HSM2HOST manual.

2. When on-site, press the device enroll button.

Note: If the wireless device has been powered for more than 48

hours without being enrolled, tamper and restore the device to

enroll it.

Perform a Placement Test

Before permanently mounting any wireless device, temporarily

mount the device and perform a Placement test.

1. Tamper the device by removing the cover.

2. Restore the tamper. The device now enters Placement test

mode for 15 minutes.

3. Trip the device and the red LED blinks once to identify that a

signal is being sent to the receiver and then blinks three times

to identify the signal strength. To perform a walk test, walk

across the far end of coverage pattern in both directions. The

following table indicates the received signal strength indica-

tion.

LED Response

Signal Strength

Green LED blinks

STRONG

Orange LED blinks

GOOD

Red LED blinks

POOR

No blinks

No communication

IMPORTANT! Only GOOD or STRONG signal strengths are

acceptable. If you receive a POOR signal from the device, re-

locate it and re-test until a GOOD or STRONG signal is

received.

Note: For UL/ULC installations, only STRONG signal levels

are acceptable. After installation verify the product functional-

ity in conjunction with the compatible receivers HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920.

Note: For detailed Placement instructions refer to the control

panel Reference Guide.

Note: Perform a walk test of the coverage area at least once a

year to ensure that the detector is working correctly.

Mounting

Note: Mount the detector so that its orientation is perpendicular

to the expected intrusion path. For the desired detector's range

and height, use mounting holes x or y, as specified in the table

below.

Note: To be installed by service persons in non-hazardous loca-

tions only.

Use the following as a guide for locating a suitable mounting

location:

• Keep away from heat sources.

• Do not expose to air drafts.

• Do not install outdoors.

• Avoid direct sunshine.

• Keep wiring away from power cables.

• Do not install behind partitions.

• Mount on solid stable surface.

3.0

2.7

2.4

2.1

1.8

60 ft

15 m

Caution! The back tamper switch will not protect the unit

unless the break-away base segment is secured to the wall with

at least one screw.

Configuration

To enter the wireless configuration section enter [804][000].

Device Toggles

[001][01]

Alarm LED - Default [Y]

Enables the devices LED to activate when an alarm

event occurs.

[001][04]

Supervision - Default [Y]

Enables supervision of the device.

Selections

[003]

Hightraffic Shutdown - Default [01]

Activating this feature helps conserve battery power

when the system is disarmed by configuring a reporting

timer. When motion is detected, the device transmits an

alarm to the receiver and will not report any further

events until the timer expires. Any motion detected

during the configured period will be reported once the

timer expires. No Delay causes the device to report an

alarm each time the detector is tripped.

[01] Detector Dis-

[02] No Delay

[03] 5 second

abled (while dis-

delay

armed)

[04] 15 second

[05] 30 second

[06] 1m delay

delay

[07] 5m delay

[08] 10m delay

[09] 20m delay

[10] 60m delay

Event counter - Default [002]

[016]

Alarm activates after a configured number of events

have been detected.

Key in activities

001-255

Event Indications

LED Indications

Event

Red LED blinks

Stabilization (warm-up 120

sec)

Red LED ON 0.2 sec.

Tamper open / close

Red on 2 sec.

Intruder alarm

Yellow LED on

AM detection – Diagnostic

mode

Yellow LED blinks slowly

AM detection – Normal

(0.2 sec. ON, 30 sec. OFF)

mode

LED Indications

Event

Yellow and red LED blink

Self-test failure – Diagnostic

simultaneously (0.2 sec. ON

mode

[both], 0.2 sec. OFF)

Yellow and red LED blink

Self-test failure – Normal

simultaneously slowly (0.2

mode

sec. ON [both], 30 sec. OFF)

Specifications

GENERAL

Detector Type: Dual element low-noise pyroelectric sensor

Lens Data

No. of Beam Elements:18x3=54 far parabolic mirror seg-

ments

10m

32. 8ft

16. 4ft

10m

32. 8ft

15 m

16.4

32. 8

49.2 ft

2.1 m

(6.9 ft)

15 m

16.4

32.8

49.2 ft

Max. Coverage: 15 m (49 ft) / 90°25 m (82 ft) x 2.5 m

Pet Immunity (only): Up to 38 kg (85 lb)

ELECTRICAL

Internal Battery: 3V Lithium battery, type CR-123A (option-

ally can be used type CR-17450)

Note: For UL installations use Gold Peak (GP) only. Use only

the above battery type.

Nominal Battery Capacity: 1450 mA/h ( 2400mA/h for

optional CR17450)

Low Battery Threshold: 2.45 V

Battery Life (for typical use): 7 years (not tested by UL/ULC)

FUNCTIONAL

True Motion Event Verification: 2 remote selections - 1

(OFF) or 2 (ON) motion events

Alarm Period: 2 seconds

WIRELESS

Frequency Band (MHz): CE Listed PG4974: 433MHz; CE/

EN listed PG8974: 868MHz; FCC/IC/UL/ULC listed PG9974:

912-919MHz

Communication Protocol: PowerG

Supervision: Signaling at 4-min. intervals

Tamper Alert: Reported when a tamper event occurs and in

any subsequent message, until the tamper switch is restored

MOUNTING

Height: 1.8 – 3.0 m (6 - 10 ft).

Installation Options: Surface or corner

ACCESSORIES

PGBRACKET-1: Surface mounted swivel bracket, adjustable

30° down and 45° left/45° right.

PGBRACKET-2: PGBRACKET-1 with a corner adapter

PGBRACKET-3: PGBRACKET-1 with a ceiling adapter

Note: UL did not evaluate the product with the use of brackets.

ENVIRONMENTAL

RFI Protection: >20 V/m up to 2000 MHz, excluding inband

frequencies

Temperature range: -10°C to +55°C (UL/ULC only verified

the range 0ºC-49ºC)

Relative Humidity: up to max. 93%RH, non-condensing

PHYSICAL

Size (H x W x D): 115 x 60 x 48 mm (4-1/2 x 2-5/16 x 1-15/

16")

Weight (with battery): 90 g (3 oz).

Color: White

COMPATIBLE RECEIVERS

433MHz Band: HSM2HOST4; HS2LCDRF(P)4;HS2IC-

NRF(P)4; PG4920

868MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8;PG8920

912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9; HS2IC-

NRF(P)9; PG9920

Note: Only devices operating in band 912-919MHz are UL/

ULC listed.

UL/ULC Notes

Only model PG9974 operating in the frequency band 912-

919MHz is UL/ULC listed. The PG9974 has been listed by UL

for commercial and residential burglary applications and by

ULC for residential burglary applications in accordance with

the requirements in the Standards UL 639 and ULC-S306 for

Intrusion Detection Units.

For UL/ULC installations use these devices only in conjunction

with compatible DSC wireless receivers: HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920. After installa-

tion verify the product functionality in conjunction with the

compatible receiver used.

Europe: The PG8974 and PG4974 are compliant with the RTTE

requirements - Directive 1999/5/EC of the European Parliament

and of the Council of 9 March 1999. Model PG8974 certified by

DNV (DET NORSKE VERITAS) to the following standards:

EN50131-2-2, EN50131-1 GRADE 2, CLASS II, EN50131-6 Type C. DNV (DET

NORSKE VERITAS) has certified only the 868 MHz variant of this product.

According to EN 50131-1:2006 and A1:2009, this equipment can be applied in

installed systems up to and including Security Grade 2, Environmental Class II.

UK: The PG8974 is suitable for use in systems installed to conform to

PD6662:2010 at Grade 2 and environmental class 2. BS8243 The Power G

peripheral devices have two- way communication functionality, providing

additional benefits as described in the technical brochure. This functionality has

not been tested to comply with the respective technical requirements and should

therefore be considered outside the scope of the product's certification

FCC COMPLIANCE STATEMENT

WARNING! Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in residential

installations. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio and television reception.

However, there is no guarantee that interference will not occur in a particular

installation. If this device does cause such interference, which can be verified by

turning the device off and on, the user is encouraged to eliminate the interference

by one or more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the one that supplies

power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

This equipment complies with FCC and IC RF radiation exposure limits set forth

for an uncontrolled environment.

This device complies with FCC Rules Part 15 and with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept

any interference that may be received or that may cause undesired operation.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisee aux deux

conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si

le brouillage est susceptible d'en compromettre le fonctionnement.