Foxfury Lighting Solutions 200-FF261-5 사용 설명서 - 페이지 4
{카테고리_이름} Foxfury Lighting Solutions 200-FF261-5에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Foxfury Lighting Solutions 200-FF261-5 5 페이지. Intrinsic safety headlamp
페이지 인쇄
Warnings
- continued
WARNING: Due to the nature of where the Intrinsic Safety Model FF261 may be used, DO NOT operate or
use the unit in a hazardous location with a broken or cracked LED. Quickly rotate the battery pack switch
to "OFF" if a LED is broken while in a hazardous area or zone, by turning the battery pack cap to
"OFF" - rotate cap COUNTER- CLOCKWISE, at least a half-turn past when the unit shuts down.
WARNING: If the unit is dropped from a height of more than 8 ft/2.4 m, it is recommended that the unit
be turned off until it can be inspected for cracked or broken LED's outside of any hazardous location areas.
WARNING: Do not subject the unit's headpiece to bending or twisting motions. It contains a printed
circuit board (PCB) that is conformally coated, while the coating is flexible; excessive bending or twisting
can cause the coating to fail and lose its integrity. This is most important when exposed to temperatures,
below freezing.
WARNING: Any motion or drop that is severe enough to pop out the back-plate from the headpiece, is
cause to remove the unit from use (remove from service) and return it to the factory. Where the unit can
be inspected and repaired as necessary, before the unit is returned to normal use.
WARNING: Lights are strong enough to cause damage to the human eye. Do not stare into LEDs for long
periods of time or from a close range (less than 2 ft).
FoxFury LLC is not responsible for the incorrect use of the FoxFury Lighting product. Usage of this product must be supervised by an
adult when used by a minor.
FoxFury LLC is not responsible for any injury or damage caused during the use of this product.
Any FoxFury product should be operated at speeds safe enough to maneuver around surrounding obstacles.
Do not use under the influence of drugs or alcohol.
Important
---
In case an LED gets broken:
The FoxFury unit is designed to take a fall, even several, from a height of 30 feet or less onto a concrete floor.
However, it may hit a small or protruding object that could crack an LED.
If the unit is dropped from a height of more than 8 feet, it is recommended that the unit be turned off
until it can be inspected for cracked or broken LEDs outside of any hazardous location areas. Use an
almost exhausted set of batteries when checking for cracked LEDs - a dim light output makes checking
easier, a pair of sunglasses may help.
A broken or malfunctioning LED can cause a decrease in battery life.
Due to the sealants coating the electronics, your FoxFury Lighting Product must be returned to FoxFury in order to assess how best to
proceed in fixing the unit. Do not attempt to repair the unit yourself.
The battery pack contains a fast-acting fuse and a fusible resistor, neither of which can be replaced by a user; return the unit to
FoxFury for replacement of the battery pack section.
GENERAL CARE & USE
Treat FoxFury Lighting Systems lights the same way you would an expensive pair of glasses or goggles.
- Before each use of the unit. Check that both 'O'-rings are present, have no nicks and are greased. If
additional grease is required, use a silicone-based lubricant grease around the grooves and both 'O'-ring
seals on the battery pack, to ease turning of the battery cap, and to insure a gas-tight seal.
- A new set of replacement 'O'-rings may be ordered from FoxFury, LLC; or on-line from www.FoxFury.com. Use ONLY
'O'-rings supplied by FoxFury, LLC or via FoxFury.com to keep the unit rated as Intrinsically Safe, to UL-913. Order P/N
FF261-BPOR for the replacement 'O'-ring set of two. A set of spare O-rings is supplied with each unit purchased.
- Do not subject the unit's headpiece to bending or twisting motions.
- Any motion or drop that is severe enough to pop out the back-plate from the headpiece, is cause to remove the unit
from use (remove from service) and return it to the factory, where an additional coating layer can be applied and
tested, before the unit is returned to normal use.
- The first (lower) 'O'-ring is necessary to create a water tight seal. The unit becomes WATERPROOF when just the first 'O'-ring is
installed. For repairs or replacement, simply slip the old 'O'-ring off and install a new one onto the threaded neck of the battery
pack. The cap will become stiffer to turn until a small amount of silicone grease is applied. Applying a small amount of silicone
grease is required after cleaning, or replacement, and as part of normal user maintenance.
- The second (upper) 'O'-ring helps to make the unit explosion proof. After placing this second 'O'-ring on the battery pack, the cap
will be slightly more difficult to turn even with the proper amount of silicone grease applied. When the difficulty of turning the cap
increases again during use, take it as notice to apply more silicone grease – to keep the unit rated as intrinsically safe.
This also makes it easier for you, as the user to turn the unit ON or OFF.
FF261-x INSTRUCTION Sheet_5_14
Page 4