DSC Power Series PC5904 설치 지침

{카테고리_이름} DSC Power Series PC5904에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC Power Series PC5904 2 페이지. Intercom talk / listen module

페이지 인쇄

PC5904 Installation Instructions

Intercom Talk/Listen Module

This equipment shall be installed in non-hazardous locations,

by service persons only. These instructions must be used with

the PC5900 Installation Manual.

The PC5904 Central Station Talk/Listen module is used in

conjunction with the PC5900 for communication with the

central monitoring station. Each PC5904 station has a separate

microphone and speaker to transmit and receive audio input.

Monitoring station personnel can listen in and respond via the

control station loud speaker when required.

Wire each station directly to the PC5900 using shielded

22-gauge, 4-conductor wire.

Specifications

• PC5904 maximum current draw: 175mA

• Operating Temperature: -10°C to +55°C

• Relative Humidity: 93% (max.)

Mounting and Wiring Directions

Prior to installation, disconnect

IMPORTANT NOTE:

power and telephone line connection.

1. Position the PC5904 backplate in the desired location and

mark the appropriate screw locations.

2. Secure the PC5904 backplate to the wall using the

supplied screws, as indicated below:

WALL

29 0 0 1 9 0 8 R0 0 4

Toronto, Canada www.dsc.com

Tech. Support: 1-800-387-3630 (Canada & U.S.), 905-760-3000

3. Wire the station to the PC5900. To wire the power, connect

the +VS to AUX and GND to COM (red = positive; black =

negative). The MIC and SPK terminals on each PC5904

must be connected to an M terminal (M1-M4) and a SPK

terminal on the PC5900 as indicated below:

PC5900

RED BLK YEL GRN

There are two AUX and COM terminals located on the

NOTE:

PC5900. The PC5904 can be connected to either terminal.

4. The speaker volume and microphone sensitivity can be

adjusted with the MIC and SPK potentiometers, as

indicated in the diagram above.

5. Once all wiring is complete, mount the station to the

backplate.

It is recommended that wall anchors be used for all

NOTE:

mounting screws. When the wall anchors have been installed,

secure the backplate to the wall.

BACKPLATE

AUX

COM

M3 M4 SPK

RNG TIP

R-1 T-1

LIMITED WARRANTY

Digital Security Controls warrants that for a period of twelve months from the

date of purchase, the product shall be free of defects in materials and workman-

ship under normal use and that in fulfillment of any breach of such warranty,

Digital Security Controls shall, at its option, repair or replace the defective

equipment upon return of the equipment to its factory. This warranty applies

only to defects in parts and workmanship and not to damage incurred in ship-

ping or handling, or damage due to causes beyond the control of Digital Secu-

rity Controls such as lightning, excessive voltage, mechanical shock, water

damage, or damage arising out of abuse, alteration or improper application of

the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be

in lieu of any and all other warranties, whether expressed or implied and of all

other obligations or liabilities on the part of Digital Security Controls. This war-

ranty contains the entire warranty. Digital Security Controls neither assumes

responsibility for, nor authorizes any other person purporting to act on its behalf to

modify or to change this warranty, nor to assume for it any other warranty or lia-

bility concerning this product. In no event shall Digital Security Controls be liable

for any direct or indirect or consequential damages, loss of anticipated profits, loss

of time or any other losses incurred by the buyer in connection with the purchase,

installation or operation or failure of this product.

Warning: Digital Security Controls recommends that the entire system be

completely tested on a regular basis. However, despite frequent testing, and

due to, but not limited to, criminal tampering or electrical disruption, it is pos-

sible for this product to fail to perform as expected.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Con-

trols could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed

and used properly, in strict accordance with the manufacturer's instructions,

may cause interference to radio and television reception. It has been type tested

and found to comply with the limits for Class B device in accordance with the

specifications in Subpart "B" of Part 15 of FCC Rules, which are designed to

provide reasonable protection against such interference in any residential

installation. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause interference to television or

radio reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Re-orient the receiving antenna

• Relocate the alarm control with respect to the receiver

• Move the alarm control away from the receiver

• Connect the alarm control into a different outlet so that alarm control and

receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television

technician for additional suggestions. The user may find the following booklet

prepared by the FCC useful: "How to Identify and Resolve Radio/Television

Interference Problems". This booklet is available from the U.S. Government

Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

Printed in Canada