DSG Technology GoldStar 970 빠른 시작

{카테고리_이름} DSG Technology GoldStar 970에 대한 빠른 시작을 온라인으로 검색하거나 PDF를 다운로드하세요. DSG Technology GoldStar 970 2 페이지.

1. Before You Start
If you are a modem dialup user:
Subscribe to an Internet access account from your local ISP. You'll be given
the following information:
(1) The local Internet access phone number (2) User Name or User ID (3) Password
Note:
functions only with standard PPP (Point-to-Point) Internet access. It is
not compatible with certain proprietary commercial services, such as American
Online (AOL).
If you are an Ethernet user:
Subscribe to an Internet access line from your local ISP. It could be ADSL, Cable modem or leased line. You will be given the following information:
(1) Available IP address (2) Gateway IP address (3) Subnet mask
3. Input Internet Connection Information
Please refer to the right diagrams and follow the instructions below to input the Internet connection information.
(1) Press and hold the
button for 2 seconds
and the LCD screen will show
Pick up the telephone handset and press
again to select
Modem Dialup
by pressing the
button on your telephone
keypad.
(2) Press
again to save and exit. When you set
the
to
Modem Dialup
screen will show IP980M. If you set it to
mode, the LCD screen will show IP980E.
Follow the steps below when using the Modem dialup mode:
(1) Press and hold
for 2 seconds. Pick up the phone and press
access to
ISP PHONE
NO. and press
(2) Use your telephone keypad to input your Internet access phone number. Press
(3) Press
and the screen will show
(4) Press
again to access to
press
on your telephone keypad. Press
(5) Now you've entered Internet connection information. Press
Note: ISP Test
If you use modem dialup for your Internet connection, you may want to verify if you have entered correct Internet connection information. After you
completed
3. Input Internet Connection
(1) Press and hold
for 2 seconds and the screen will show
see
MODEM
SETUP.
(2) Press
and then
several times until you see
(3) Press
to start
ISP
TEST.
to 50 seconds.
(4) After the
ISP TEST
is completed, there are two possible results:
(a) If the screen shows
ISP
(b) If the screen shows
ISP
congested at this time. Please try the
entered is correct. Or contact your ISP to check your account status.
(5) Press
several times until the screen shows
again to exit the setup.
Follow the steps below when using the Ethernet mode:
Press and hold
for 2 seconds. Pick up the telephone handset and press
Press
to access to
IP
TYPE. Press
save and exit.
< Control Panel >
WORKING
MODE.
or
Ethernet
mode
mode, the LCD
back to previous option
select desired character
Ethernet
again to edit this item.
ISP USER
ID. Press
ISP
PASSWORD. Press
to edit this item. Input your
Information, you can perform
WORKING
ISP TEST
will test the Internet connection information you entered. Please wait for the testing result. This test will take 30
SUCCESS, you've successfully completed your setting.
FAIL, there might be some errors while you entered your Internet connection information or the Internet is heavily
ISP TEST
again later. If the result remains FAIL, please check if the Internet connection information you
EXIT TO
MAIN. Press
again to edit this item and press
Quick Start for
Quick Start for
2. Installation of
Please refer to the following diagram for installation.
Wall Power Socket
AC/DC Adaptor
forward to next option
select desired character
enter/exit the option
several times until the LCD display shows
to save and exit.
to edit this item. After inputting your
ISP
PASSWORD. For example: to enter "123",
on your
to save and exit.
several times until you see
EXIT
ISP TEST
by the following steps.
MODE. Pick up the telephone handset and press
on the screen.
to exit, and press
several times until the LCD display shows
or
to select
Static
LAN
DC 12V
Line
TCP/IP Networks
< Key & Characters >
Key
Characters
1 ~ ! # $ % ^ & * ( ) _
+ : " < > ? - =; ' /
2 a b c A B C
3 d e f D E F
4 g h i G H I
5 j k l J K L
6 m n o M N O
7 p q r s P Q R S
8 t u v T U V
9 w x y z W X Y Z
0 . , @
back to previous option
*
#
MODEM
SETUP. Press
ISP USER
ID, press
again to save and exit.
SETUP. Press
to save and exit.
several times until you
several times until you see
EXIT
ETHERNET
IP,
DHCP
or
ADSL
PPPoE. Press
Wall RJ11 Phone Jack
Internet/Intranet
< Keypad >
forward to next option
enter the option
to
SETUP. Press
SETUP.
again to