Atsumi Electric ZSL10 사용 설명서
{카테고리_이름} Atsumi Electric ZSL10에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Atsumi Electric ZSL10 3 페이지. Smart lock
페이지 인쇄S m a r t L o c k
Z S L 1 0
<Introduction>
This document describes the Smart Lock overview and how to use the
Z-Wave
functionality.
TM
This product "ZSL10" can remotely lock and unlock the door and check
the status by remote control.
This device is a security enabled Z-Wave Plus
encrypted Z-Wave Plus
messages to communicate to other security
TM
enabled Z-Wave Plus
products.
TM
This device must be used in conjunction with a S2 Security Enabled
Z-Wave
Controller in order to fully utilize all implemented functions.
TM
This product can be operated in any Z-Wave
Z-Wave
certi ed devices from other manufacturers.
TM
All non-battery operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
SmartStart enabled products can be added into a Z-Wave
scanning the Z-Wave
QR Code present on the product with a controller
TM
providing SmartStart inclusion. No further action is required and the
SmartStart product will be added automatically within 10 minutes of
being switched on in the network vicinity.
QR code and Full DSK is located inside the battery box of IN BODY and
on the packing box.
Part Names
IN - BODY
Front side
(3)
(1)
(4)
(2)
(1) Battery cover
(2) O/C Button
OUT - BODY
Front side
(1)
(2)
(1) Keypad
(2) Smart card reader
product that is able to use
TM
network with other
TM
network by
TM
Inside
Inside the battery box
(6)
(7)
(5)
(3) Battery holder
(6) Battery box
(4) EX Button
(7) QR code and
(5) SET Button
Full DSK
Operation
1. Insert batteries
Remove the battery cover of INBODY.
Install AA batteries in the battery case. 4*AA(Alkaline or lithium)
Wait for a while, a beep will sound and the o/c button will blink blue.
When the blinking goes o , the startup is complete.
2-1. Add (Inclusion) - SmartStart
Add the smart lock DSK into the primary controller SmartStart
Provisioning List.
(If your controller does not support SmartStart inclusion, please refer to
the manual for your controller for non-SmartStart inclusion.)
2-2. Add - Normal Inclusion
Set the controller in "Add(Inclusion)" mode.
For the operation procedure, see the instruction manual of the controller.
Press the SET button for about 5 seconds to start the registration
operation and the O / C button will blink blue and beeps twice.
Inclusion takes about 1 minute. Please con rm the inclusion is complete.
After that, it ashes red, but this is not related to the success / failure of
inclusion.
Press the SET button for about 5 seconds.
3. Remove (Exclusion)
Set the controller in "Remove(Exclusion)" mode.
For the operation procedure, see the instruction manual of the controller.
Press the SET button for about 5 seconds to start the registration
operation and the O / C button will blink blue and beeps twice.
Please con rm the inclusion is complete.
After that, it ashes red, but this is not related to the success / failure of
inclusion.
Press the SET button for about 5 seconds.
4. Factory Default Reset
[ NOTE ]
Use this procedure only in the event that the primary controller is lost.
The controller information are cleared.
The lock settings and user information do not change.
Press the SET button three times in two seconds to start the reset
operation and the O/C button will blink red and beeps.
Press the SET button three times in two seconds.