Airtocheck RM-402T 빠른 매뉴얼 - 페이지 2

{카테고리_이름} Airtocheck RM-402T에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Airtocheck RM-402T 2 페이지.

페이지 인쇄

1. P- Connection point for pressure sensor 1, 2, 3, 4

P- Negative pressure hose connection for channel 1, 2, 3*, 4*.

Attention! Press the hose gently into the nozzle. By pushing the hose too far, the hose

can get stuck. To remove the hose, press the blue ring and gently pull out the hose.

Only use the original supplied hoses.

2. P+ Measuring point overpressure channel 1, 2, 3, 4

P+ Measuring point overpressure for channel 1, 2, 3*, 4* (do not connect any hose!).

3. External relays blok channel 1, 2, 3, 4

External relay block connection for channel 1, 2, 3*, 4*.

4. External horn

Combined external horn connection for channel 1, 2, 3*, 4*.

5. Printer

Thermal printer for 25 meters thermal printing roll.

Attention! Place the print roll in the right direction of rotation.

6. Paper feed button

Attention! Never pull on the print roll. This may damage the printer! For paper feed,

use the paper feed button on the printer.

7. On off switch

On and off button + options for closing the project.

8. Touchscreen

Touchscreen for display and control monitor.

9. Location SD-card

Remove the cover to install/remove the SD card.

10. Location SIM-card

Remove the cover to install/remove the SIM card.

11. Storage 12-Volt adapter

Internal storage for the 12-volt adapter.

12. Inlet 12-Volt adapter

Inlet for 12-Volt adapter. Only use the supplied adapter! Using any other adapter may

result in fire or damage to the monitor.

13. Date

Date display. The date can be adjusted in; Settings (26) > System > Date Time**.

14. Time

Time display. The time can be adjusted in: Settings (26) > System > Date & Time**.

- 27

15. SD-Card

- 28

This icon indicates the status of the SD card.

SD card missing.

- 29

16. Send data

This icon indicates the status of sending data*.

Internet off.

17. Signal strength

This icon indicates the status of the signal strength.

18. Power supply

This icon indicates the status of the power supply.

19. Channel display per channel 1, 2, 3*, 4*

Display measured value, (containment) name and status for each channel. Tapping on

the "channel" will take you to the channel's quick settings menu for adjusting the

settings. More settings can be adjusted in: Settings (26) > Channel > Channel #.

20. Containment name

Displays the name of the channel/containment.***

21. Channel number

Displays the channel number (1, 2, 3*, 4*).

22. Measured value (in Pa)

Displays measured value negative pressure, measured values are always displayed in

Pascal (Pa). Values within measuring limit*** will be displayed in green, Values outside

measuring limit will be displayed in red. The text Off will be displayed when a channel

is turned off.

23. Relays block

This icon indicates the status of the relay block***.

24. Minimum / maximum negative pressure value

Displays the minimum and maximum set negative pressure value for the alarm. The

channel's shortcut menu allows you to quickly switch between

modes.

The values can be set in; Settings (26) > Channel > Channel #.

25. Project name / Monitor name

Display of project name/monitor name.

This name can be changed in; Input Project name/Monitor name

26. Settings menu

Tapping on this will open the settings menu.

27. Horn on/off

Tapping on this will switch the internal and (optional) external horn

28. Printer on/off

Tapping on this will switch printer

29. Input Project Name/Monitor Name

Tapping on this will open the (project) name input.

Channel 3 and 4 are optional (RM-404T)

** Date and time of web-based monitors are synchronized according to the provider's

system time.

*** Can be adjusted in the channel's quick settings menu.

Or in: Settings (26) > Channel > Channel #.

activated (up to a max. of -35 Pa).

on,

off or

Status OK,

Status not OK,

Status OK,

Status not OK,

Status OK,

Status not OK.

AC power,

battery.

standby,

work and

rest

(29)

on or

off.

status not OK.