3One data IRT5300-AW-5T2D 빠른 설치 매뉴얼 - 페이지 2

{카테고리_이름} 3One data IRT5300-AW-5T2D에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3One data IRT5300-AW-5T2D 4 페이지. Industrial 4g router

페이지 인쇄

surrounding between 5%~95% without condensation.

Before power on, please confirm the supported power



supply specification to avoid over-voltage damaging the

device.

The device surface temperature is high after running,



please avoid any direct contact in case of scalding.

【DIN-Rail Mounting】

For convenient usage in industrial environments, the product

adopts 35mm DIN-Rail mounting, mounting steps as below:

Step 1

Check if the DIN-Rail mounting kit is installed firmly.

Step 2

Insert the bottom of DIN-Rail mounting kit (one side

with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.

Tips:

Insert a little to the bottom, lift upward and then insert

to the top.

Step 3

Check and confirm the product is firmly installed on

DIN-Rail, then mounting ends.

【Disassembling DIN-Rail】

Step 1

Device power off.

Step 2

After lift the device upward slightly, first shift out the

top of DIN-Rail mounting kit, then shift out the

bottom of DIN-Rail, disassembling ends.

【Power Supply Connection】

DC power supply



The device provides 6-pin 5.08mm pitch power supply input

terminal blocks and two independent DC power supply

systems, P1 and P2, which enables two

terminals to connect to the device. It

could ensure the normal operation of

the device when one of the systems

fails, thus improving the reliability of

network operation. Voltage range: 12~48VDC.

48VDC POE power supply input



Port 5 of this device supports PoE power receiving.

Note:

Power ON operation: first connect power line to the



connection terminal of device power supply, then power

on.

Power OFF operation: first unpin the power plug, then



remove the power line, please note the operation order

above.

【DIP Switch Setting】

This device provides 4-bit DIP switch for function setting,

where "ON" is enable valid terminal. The definitions of DIP

switch are as follows:

1. Restore factory setting

2.Reboot

3. Reserved

4. Reserved

【Console Port Connection】

This device provides 1 program debugging port based on

RS232 serial port which can conduct device CLI command

line management by connecting to PC. The interface adopts

RJ45 port. Its pin definitions are as follows:

No.

Pin Definition

TXD

RXD

【USB Port Connection】

Reserved

【SIM Slot】

This device provides 2 SIM slots. It would pops up after you

inserting a retrieve card pin in the little hole beside the SIM

slot, and then you should put the SIM card in the slot correctly

and insert the slot back in the router.

Note:

If the SIM card needs to be changed, the device should be

power off first in case of damaging the card.

【Serial Port Connection】

or 2 RS-485 serial ports. Its pin definitions are as follows:

RS-232

TXD

RS-485

Data-

(B)

【I/O Connection】

This device provides 10-pin 3.81mm pitch I/O input terminal

blocks (I/O port is the right 4-pin) ,

this function is temporarily reserved as the picture shows

above

【Checking LED Indicator】

The device provides LED indicators to monitor its operating

status, which has simplified the overall troubleshooting

process. The function of each LED is described in the table

below:

LED

Status

WLAN

OFF

GND

This device provides 10-pin

3.81mm pitch serial port input

terminal blocks (the left 6-pin is

serial port) and supports 2 RS-232

RXD

GND

TXD

RXD

GND

Data+

GND

Data-

Data+

GND

(A)

(B)

(A)

Description

WIFI is running normally

WIFI is running abnormally or

closed

All indicators are out. It means

the LTE signal of the opposite

end is weak or no signal.

One indicator is on. It means the

LTE signal of the opposite end is

weak