Absolute Process Instruments API 4380 G HV3 P 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Absolute Process Instruments API 4380 G HV3 P에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Absolute Process Instruments API 4380 G HV3 P 2 페이지. Dc to dc transmitters, high voltage input, isolated, field rangeable

페이지 인쇄

Absolute Process Instruments API 4380 G HV3 P 빠른 시작 매뉴얼

Installation and Setup

Precautions

WARNING! All wiring must be performed by a qualified electrician

or instrumentation engineer. See diagram for terminal designations

and wiring examples. Consult factory for assistance.

WARNING! Avoid shock hazards! Turn signal input, output, and

power off before connecting or disconnecting wiring, or removing

or installing module.

Précautions

ATTENTION! Tout le câblage doit être effectué par un électricien

ou ingénieur en instrumentation qualifié. Voir le diagramme pour

désignations des bornes et des exemples de câblage. Consulter

l'usine pour assistance.

ATTENTION! Éviter les risques de choc! Fermez le signal d'entrée,

le signal de sortie et l'alimentation électrique avant de connecter ou

de déconnecter le câblage, ou de retirer ou d'installer le module.

API maintains a constant effort to upgrade and improve its products.

Specifications are subject to change without notice. See api-usa.com for

latest product information. Consult factory for your specific requirements.

WARNING: This product can expose you to chemicals includ-

ing lead and nickel, which are known to the State of California

to cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

Socket and Mounting

The module installation requires a protective panel or enclosure. Use

API 008 or finger-safe API 008 FS socket. See specifications for maxi-

mum allowable socket voltages. Note that some relay sockets may

have lower voltage ratings. The socket clips to a standard 35 mm DIN

Input

4380G HV3

Select

Output

Select

1. Set Output select switch as required.

2. From Table, set 'ABC' and Input

select switches for specific

Input/Output range.

3. Set Zero/Span controls.

rail or can be attached to a flat surface using the two mounting holes.

Range Selection

Two slide switches and three rotary switches located on the side of

the module are used to select input and output ranges. Most popu-

lar ranges are listed on the module label. See table below. Special

ranges will be indicated on the model/serial number module label.

1. Unplug the module from its socket. Do not change ranges while

the module is powered.

2. Locate the switch combination for your desired input and output

ranges from the table.

3. Set the OUTPUT SELECT slide switch to current (I) or voltage (V)

depending on output type.

4. Set the three rotary switches A, B, and C to the values found in

the table.

Output

0-1 V

0-2 V

Switches

ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O ABC I O

Input

0-1 V

0 8 1H V 18 1H V 281HV 3 8 1 H V 2 8 3 H V 5 8 1 H V 5 8 3 H V 6 8 1 H V 88 1H V 981 HV 08 1H I 3 81 HI 28 3H I 5 81 HI 58 3HI 6 81 HI

0-2 V

0 9 1H V 19 1H V 291HV 3 9 1 H V 2 9 3 H V 5 9 1 H V 5 9 3 H V 6 9 1 H V 89 1H V 991 HV 09 1H I 3 91 HI 29 3H I 5 91 HI 59 3HI 6 91 HI

0 A 1L V 1A 1L V 2A1LV 3 A 1 L V 2 A 3 L V 5 A 1 L V 5 A 3 L V 6 A 1 L V 8A 1L V 9A1 LV 0A 1L I 3 A1 LI 2A 3L I 5 A1 LI 5A 3LI 6 A1 LI

0-3 V

0-4 V

0 A 1H V 1A 1H V 2A1HV 3 A 1 H V 2 A 3 H V 5 A 1 H V 5 A 3 H V 6 A 1 H V 8A 1H V 9A1 HV 0A 1H I 3 A1 HI 2A 3H I 5 A1 HI 5A 3HI 6 A1 HI

0-5 V

0 C 1H V 1C 1H V 2C1HV 3 C 1 H V 2 C 3 H V 5 C 1 H V 5 C 3 H V 6 C 1 H V 8C 1H V 9C1 HV 0C 1H I 3 C1 HI 2C 3H I 5 C1 HI 5C 3HI 6 C1 HI

0-8 V

0 B 1H V 1B 1H V 2B1HV 3 B 1 H V 2 B 3 H V 5 B 1 H V 5 B 3 H V 6 B 1 H V 8B 1H V 9B1 HV 0B 1H I 3 B1 HI 2B 3H I 5 B1 HI 5B 3HI 6 B1 HI

0-10 V

0 0 1H V 10 1H V 201HV 3 0 1 H V 2 0 3 H V 5 0 1 H V 5 0 3 H V 6 0 1 H V 80 1H V 901 HV 00 1H I 3 01 HI 20 3H I 5 01 HI 50 3HI 6 01 HI

0-15 V

0 1 1L V 11 1L V 211LV 3 1 1 L V 2 1 3 L V 5 1 1 L V 5 1 3 L V 6 1 1 L V 81 1L V 911 LV 01 1L I 3 11 LI 21 3L I 5 11 LI 51 3LI 6 11 LI

0-20 V

0 1 1H V 11 1H V 211HV 3 1 1 H V 2 1 3 H V 5 1 1 H V 5 1 3 H V 6 1 1 H V 81 1H V 911 HV 01 1H I 3 11 HI 21 3H I 5 11 HI 51 3HI 6 11 HI

0-30 V

0 2 1L V 12 1L V 221LV 3 2 1 L V 2 2 3 L V 5 2 1 L V 5 2 3 L V 6 2 1 L V 82 1L V 921 LV 02 1L I 3 21 LI 22 3L I 5 21 LI 52 3LI 6 21 LI

0-40 V

0 2 1H V 12 1H V 221HV 3 2 1 H V 2 2 3 H V 5 2 1 H V 5 2 3 H V 6 2 1 H V 82 1H V 921 HV 02 1H I 3 21 HI 22 3H I 5 21 HI 52 3HI 6 21 HI

0-50 V

0 4 1H V 14 1H V 241HV 3 4 1 H V 2 4 3 H V 5 4 1 H V 5 4 3 H V 6 4 1 H V 84 1H V 941 HV 04 1H I 3 41 HI 24 3H I 5 41 HI 54 3HI 6 41 HI

0-60 V

0 3 1L V 13 1L V 231LV 3 3 1 L V 2 3 3 L V 5 3 1 L V 5 3 3 L V 6 3 1 L V 83 1L V 931 LV 03 1L I 3 31 LI 23 3L I 5 31 LI 53 3LI 6 31 LI

0-75 V

0 5 1L V 15 1L V 251LV 3 5 1 L V 2 5 3 L V 5 5 1 L V 5 5 3 L V 6 5 1 L V 85 1L V 951 LV 05 1L I 3 51 LI 25 3L I 5 51 LI 55 3LI 6 51 LI

0-80 V

0 3 1H V 13 1H V 231HV 3 3 1 H V 2 3 3 H V 5 3 1 H V 5 3 3 H V 6 3 1 H V 83 1H V 931 HV 03 1H I 3 31 HI 23 3H I 5 31 HI 53 3HI 6 31 HI

0 3 FH V 13 FH V 23FHV 3 3 F H V 2 3 1 H V 5 3 F H V 5 3 1 H V 6 3 F H V 83 FH V 93F HV 03 FH I 3 3F HI 23 1H I 5 3F HI 53 1HI 6 3F HI

20-100 V

0-100 V

0 5 1H V 15 1H V 251HV 3 5 1 H V 2 5 3 H V 5 5 1 H V 5 5 3 H V 6 5 1 H V 85 1H V 951 HV 05 1H I 3 51 HI 25 3H I 5 51 HI 55 3HI 6 51 HI

0-150 V

0 6 1L V 16 1L V 261LV 3 6 1 L V 2 6 3 L V 5 6 1 L V 5 6 3 L V 6 6 1 L V 86 1L V 961 LV 06 1L I 3 61 LI 26 3L I 5 61 LI 56 3LI 6 61 LI

0-200 V

0 6 1H V 16 1H V 261HV 3 6 1 H V 2 6 3 H V 5 6 1 H V 5 6 3 H V 6 6 1 H V 86 1H V 961 HV 06 1H I 3 61 HI 26 3H I 5 61 HI 56 3HI 6 61 HI

±75 V

0 6 4L V 16 4L V 264LV 3 6 4 L V 2 6 6 L V 5 6 4 L V 5 6 6 L V 6 6 4 L V 86 4L V 964 LV 06 4L I 3 64 LI 26 6L I 5 64 LI 56 6LI 6 64 LI

±100 V

0 6 4H V 16 4H V 264HV 3 6 4 H V 2 6 6 H V 5 6 4 H V 5 6 6 H V 6 6 4 H V 86 4H V 964 HV 06 4H I 3 64 HI 26 6H I 5 64 HI 56 6HI 6 64 HI

0 7 4L V 17 4L V 274LV 3 7 4 L V 2 7 6 L V 5 7 4 3 V 5 7 6 L V 6 7 4 L V 87 4L V 974 LV 07 4L I 3 74 LI 27 6L I 5 74 LI 57 6LI 6 74 LI

±150 V

±200 V

0 7 4H V 17 4H V 274HV 3 7 4 H V 2 7 6 H V 5 7 4 H V 5 7 6 H V 6 7 4 H V 87 4H V 974 HV 07 4H I 3 74 HI 27 6H I 5 74 HI 57 6HI 6 74 HI

www.mod-tronic.com | [email protected] | 1-800-794-5883

5. Set the INPUT SELECT slide switch to L or H depending on table

value.

6. Proceed to Calibration and Output Test Function setup. The

Zero, Span and Test Range potentiometers can now be adjusted

for the desired output range.

Depending on the rotary switch settings, the input is filtered, either

amplified or attenuated as required, then passed through an optical

isolation circuit to the output stage.

The input selector switch determines the input impedance for the

module, typically 50 W for current inputs and 1 MW or greater for

voltage inputs.

Signal Output

Polarity must be observed when connecting the signal output to the

load. The module provides 20 VDC power to the output loop when

current output is selected.

Signal Input

For safety, input must be off while connecting wiring. Connect the

signal input to terminals 5 and 6.

Module Power

Check model/serial number label for module operating voltage to

make sure it matches available power.

AC power is connected to terminals 1 and 3.

For DC powered modules, polarity MUST be observed.

Positive (+) is wired to terminal 1

Negative (–) is wired to terminal 3

Calibration

Top-mounted Zero and Span potentiometers calibrate the output.

Note: Perform the following calibration procedure any time switch

settings are changed.

1. Apply power to the module and allow a minimum 20 minute

warm up time.

2. Using an accurate calibration source, provide an input to the

module equal to the minimum input required for the application.

3. Using an accurate measurement device for the output, adjust

the Zero potentiometer for the exact minimum output desired.

The Zero control should only be adjusted when the input signal

is at its minimum. This will produce the corresponding minimum

output signal. For example: 4 mA for a 4-20 mA output or –10 V

for a ±10V output.

4. Next, set the input at maximum, then adjust the Span pot for the

exact maximum output desired. The Span control should only

be adjusted when the input signal is at its maximum. This will

produce the corresponding maximum output signal. Example:

for 4-20 mA output, the Span control will provide adjustment for

the 20 mA or high end of the signal.

5. Repeat adjustments for maximum accuracy.

Output Test Function

The Test button may be pushed to provide a fixed output when

depressed. This will drive the device on the output side of the loop

(a panel meter, chart recorder, etc.) with a known good signal that

can be used as a system diagnostic aid during initial start-up or

0-4 V

0-5 V

1-5 V

0-8 V

2-10 V

0-10 V

±5 V

±10 V

API 4380 G HV3

during troubleshooting.

It can be adjusted to vary the output signal from 0 to 100% of the cali-

brated output range. When released, the output will return to normal.

Turn the multi-turn Test Range potentiometer while holding the

Test Switch depressed until the desired output test level is reached.

Operation

The API 4380 G HV3 input is filtered, either amplified or attenuated

as required, then passed through an optical isolation circuit to the

output stage.

The green LoopTracker

input LED provides a visual indication that

a signal is being sensed by the input circuitry of the module. It also

indicates the input signal strength by changing in intensity as the

process changes from minimum to maximum.

If the LED fails to illuminate, or fails to change in intensity as the

process changes, check the module power or signal input wiring. Note

that it may be difficult to see the LEDs under bright lighting conditions.

The red LoopTracker output LED provides a visual indication that

the output signal is functioning. It becomes brighter as the input

and the corresponding output change from minimum to maximum.

For a current output, the red LED will only light if the output loop

current path is complete. For either current or voltage outputs,

failure to illuminate or a failure to change in intensity as the process

changes may indicate a problem with the module power or signal

output wiring.

Voltage or

Powered

Voltage

mA Signal

input

(–)

(+)

Socket top

view

Key down

when

panel

mounting

Sourcing mA

output

(+)

(–)

20 V loop power

PLC, Display,

Recorder w.

mA Input

Voltage output

(+)

(–)

PLC, Display,

Recorder w.

Voltage Input

0-2 mA 0-10 mA 2-10 mA 0-16 mA 4-20 mA 0-20 mA

AC or DC (–)

Module power

AC or DC

(+)