3onedata ICS5428 Series 빠른 설치 매뉴얼 - 페이지 3
{카테고리_이름} 3onedata ICS5428 Series에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3onedata ICS5428 Series 4 페이지. Unmanaged industrial ethernet switch
3onedata ICS5428 Series에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (3 페이지)
페이지 인쇄normal non alarm state, closed when any alarm information
occurs. The relay can externally connect to alarm lights or
alarm buzzer or other switching value collecting device in
order to timely notify operators when the alarm occurs.
【Console Port Connection】
The series products provide 1 program debugging port
based on RS-232 serial port which can conduct device CLI
command management after connecting to PC. The
interface adopts RJ45 port, the RJ45 pin definition as
follows:
Pin No.
2
3
Definition
TXD
RXD
【Checking LED Indicator】
The series products provide LED indicators to monitor the
device working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
PWR is connected and running
ON
normally
P1
PWR is disconnected and running
OFF
abnormally
PWR is connected and running
ON
normally
P2
PWR is disconnected and running
OFF
abnormally
Blinking
The system is running normally
The system is not running or
RUN
OFF
running abnormally
ON
System is running abnormally
Power supply or the port link is
ON
alarming.
ALM
Power and the port link have no
OFF
alarm
Link
Port has established valid
ON
(G1-G2
network connection
LED
Indicate
4/G28,
Blinking
X1-X4)
OFF
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device's configuration interface via IE
browser is shown as below:
Step 1
Configure the IP addresses of computer and the
5
device to the same network segment, and the
GND
network between them can be mutually accessed
Step 2
Enter device's IP address in the address bar of
the computer browser.
Step 3
Enter device's username and password in the
login window as shown below.
Step 4
Click "OK" button to login to the WEB interface of
the device.
Description
Port is in a network
communication status
Port hasn't established valid
network connection.
Note:
The
default
IP
address
"192.168.1.254".
The default username and password of the device is
"admin123".
If the user name or password is lost, user can restore it
to factory settings via restoring factory setting button
or management software; all modified configurations
will be cleared after restoring to factory settings, so
please backup configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
10GbE interface
10GbE SFP+ port (10Gigabit /
Gigabit self-adaption)
Gigabit SFP
1000Base-SFP slot
1000M Combo port
10/100/1000Base-T(X) RJ45
or 1000 Base-SFP interface
optional
Gigabit copper port
10/100/1000
self-adapting
half/full duplex self-adapting or
compulsive
support
self-adapting
Console port
CLI command management
port (RS-232), RJ45
Alarm interface
5-pin 5.08mm pitch terminal
block (R+/R-), support 2 relay
alarm information outputs
of
the
device
is
Base-T(X)
RJ45
port,
working
mode,
MDI/MDI-X