Attwood 5540 Series 설치 지침

{카테고리_이름} Attwood 5540 Series에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Attwood 5540 Series 2 페이지. Led anti-glare all-round lights, articulating head led light, articulating head led light w/folding pole

페이지 인쇄

LED Anti-Glare All-Round Lights

5530 Series: Articulating Head LED Light

5540 Series: Articulating Head LED Light w/Folding Pole

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69422 Rev. A

Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards

as tested by Imanna Laboratories, 5/3/2007. 2 nautical mile visibility.

CAUTION

Read all instructions carefully before installing and using this product. All positive (+12V DC)

lighting wires require a 1-amp fuse to protect circuits and vessel. The aluminum light

pole is not grounded.

MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER VOLTAGE WILL DAMAGE

LIGHT AND CIRCUITRY.

WARNING

Disconnect power when installing or servicing this product. Remove boat from water

before using any 120V AC power tools.

LOCATION

5530 and 5540 Series All-Round Lights are designed for boats up to 39.4 feet (12m).

Position the all-round light so its LED light source is not less than one meter (39.4")

above sidelights. If replacing an existing pole light, replace with a pole at least as long

as the existing pole.

Mount the all-round light in a position so that: (Figure 1)

• Light output is ﬂ at and parallel to water when boat is ﬂ oating.

• Light shines 360°, unobstructed.

• Light does not shine on operator, or reﬂ ect off any part of the boat in the operator's

ﬁ eld of vision.

Figure 1

One meter

or 39-3/8"

EXTENDING AND FOLDING THE POLE (5540 Series)

The light is shipped with the pole folded and collars locked.

1. To unlock pole: Hold folded pole with lens upright. Pull the collar down (on lens half

of the pole). Pull the opposite locking collar up. This separates the collars. (Figure 2)

CAUTION: When unfolding pole, do not pinch ﬁ ngers in hinge.

Figure 2

Locking Collar

Groove

Hinge Collar

Tab

2. Unfold pole so it is straight and threads are tight together. Slide hinge collar down

and turn onto threads. Hand-tighten only.

3. To fold and stow, reverse steps 1 and 2. Insert tab of hinge collar into groove of locking

collar. Press collars together.

INSTALLATION

Poles Without Locking Collar (5560 Series)

1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into

base (Figure 3).

Figure 3

Pole Screw

7.5

Hinge Collar

Tab

CAUTION!

Pinch Point

Hinge

Threads

Locking

Spring

•

2. Press down ﬁ rmly to engage electrical connectors. With Easy Lock Base, be sure locking

spring clicks over pole screw.

3. To remove:

• Pull locking spring back (on Easy Lock Base)

• Pull pole straight up.

Poles With Locking Collar (5530 Series)

1. Align pole screw with the slot (or locking spring) in the existing base. Insert pole into

base (Figure 4).

Figure 4

07-06

Locking

Collar

•

Lower

Ring

•

Screw

•

2. Press down ﬁ rmly to engage electrical connectors. With Easy Lock Base, be sure

locking spring clicks over pole screw.

3. Slide locking collar down to base, rotate until you can insert lower ring inside top of base.

NOTE: Locking Collar stays above the Easy Lock Base

4. On bases other than the Easy Lock Series, press collar down into base and rotate

until it tightens between pole and base.

NOTE: Periodically check pole to make sure it is secure.

5. To remove:

• Pull locking spring back (on Easy Lock Base)

• On other bases, rotate locking collar in opposite direction until it loosens,

• Pull pole straight up.

TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR

1. For bases that do not accept locking collar, remove screw at bottom of pole. Slide

locking collar off end of pole.

2. Replace screw in the upper screw hole.

TO ADJUST ANTI-GLARE ARTICULATING HEAD

For best glare reduction, adjust the light while the boat is ﬂ oating, or at the same attitude

as if it were ﬂ oating.

1. Remove the pivot screw. Pull the top pivot up and away from yoke. (Figure 5)

2. Place a small level against the lens and rotate to level position.

3. When it is level, push yoke and pivot back together. Replace and tighten screw.

(Do not over tighten.)

Figure 5

OPERATION

After installation, check lights to verify proper operation. Regulations require lights to

be operated with a three-position switch for:

1. Running lights (sidelights and all-round light);

2. Anchor lights (all-round light only);

3. Off.

BASE WIRING

IMPORTANT: LED-based lights MUST be wired for correct polarity. If your light does not

function after installation, the light base may require re-wiring. To re-wire if necessary:

1. Unscrew or remove the base so you can reach wiring.

2. Locate the connection between base wiring and the boat's wiring harness.

3. Cut wires. Add waterproof splice to each wire end.

4. Reverse polarity by reversing original wire connection to the wire harness.

5. Temporarily plug light into the base to check operation.

6. Remove light and reinstall base.

NOTE: Do not use light pole as a ﬂ agpole or handle.

MAINTENANCE

When not in use, store in Pole Light Storage Clips (Attwood #7571). Choose a storage

location where light will not be damaged or be in constant contact with water.

ATTWOOD LIMITED 10-YEAR WARRANTY

Because of the longevity of Attwood's LED lighting technology, Attwood offers a limited

10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com

for details.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Locking

Collar

•

Lower

Ring

•

Screw

•

#91020,

#91024,

or #91026

#91022

Pivot Screw

Locking

Collar

•

Locking

Spring

•