Attwood 13710-4 설치 지침

{카테고리_이름} Attwood 13710-4에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Attwood 13710-4 2 페이지. Anchor lift system

페이지 인쇄

ANCHOR LIFT SYSTEM

13710-4

INSTALLATION INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING!

Prior to drilling or mounting of the product: verify the location of all wiring harnesses,

fuel lines, steering cables etc. on your boat. Make sure all drilling and mounting

components do not interfere with the other systems of the boat.

Do not drill or place holes in areas that are or may be located below the waterline.

Always read and follow boat manufacturer's instruction manuals.

When operating boats at high speeds or in rough waters the anchor must be stowed

inside the boat to prevent accidental release of the anchor or damage to the anchor

system mount and reel components and assemblies. When trailering your boat the

anchor must be placed inside the boat and secured. Failure to do so could result

in personal injury or property damage due to possible release of the anchor during

transport.

This product is not to be used to lift humans, animals or loads other then marine

anchors. This product is not to be used where life and limb are or could be at risk.

Failure to follow all manufacturer instructions could lead to property damage and/or

personal injury and/or death.

CAUTION!

This product is designed to be used with anchors weighing up to 12 pound maximum.

Use of anchors that exceed this limit may result in personal injury or property damage

and voids all warranty of the product.

CONTENTS

• (1) quantity - Anchor Mount / Rope

Guide Assembly

• (1) quantity - Anchor Rope Reel

Assembly

• (1) quantity - Anchor Mount Rear

Pulley

• (1) quantity - Rear Pulley Axle

• (2) quantity - Push Nuts

• (6) quantity - Nylon Washers

• (1) quantity - Instruction Sheet

MATERIALS INCLUDED

Please Note: The Attwood Anchor

Lift System comes complete with the components listed

above. Due to the variety of watercraft and materials used

in the construction of boats today, Attwood has not included

mounting hardware such as bolts, screws, nuts, line guides

or pulleys. These are boat speciﬁ c and must be supplied by

the consumer to meet their particular application and craft

speciﬁ cations.

ANCHOR LIFT SYSTEM

MOUNTING INSTRUCTIONS:

It's always a good idea to enlist the help of second person during the installation

process to help in locating, holding and marking the assemblies for installation.

ANCHOR MOUNT / ROPE GUIDE INSTALLATION:

1. Determine a suitable location for the installation of the Anchor Mount / Rope Guide

Assembly and Anchor Rope Reel Assembly. Make sure that these locations have

enough support for the loads and space to properly mount and use the product with

clearances for the anchor rope to move freely during use.

For watercraft with decks or no opening in the bow plate, a 3/4 inch hole may be

necessary to be drilled directly beneath the rear roller of the Anchor Mount / Rope

Guide to provide proper routing of the anchor rope for your application.

Attwood recommends the use of swivel pulleys and guides to help route the rope to

properly utilize the Anchor Lift System by keeping the rope clear of obstructions and

to avoid undue chafﬁ ng and wear on the rope and the system. These are not supplied

but can be found at a marine dealer or online.

2. Once you have decided on the location for the Anchor Mount / Rope Guide place the

mount in position and mark, then drill the (4) holes to match the base mounting

hole positions.

3. If a ¾ inch clearance hole is required below the Anchor Mount / Rope Guide (see

ﬁ gure A) now is the time to add it. Position the mount in place and mark the center

of the rear roller along it's rear edge. Then, using this mark, drill a ¾ inch clearance

hole for the rope to pass through.

4. Attach the Anchor Mount / Rope Guide by using ¼ inch bolts or screws (depending

on your boats speciﬁ c construction and requirements), making sure all fasteners are

secure and tight.

# 69503 Rev B

Figure A

ANCHOR ROPE REEL INSTALLATION:

1. Place the Rope Reel in position and mark, and then drill, the (3) holes to match the

reel's mounting hole positions.

IMPORTANT: Make sure there is sufﬁ cient clearance for the reel to operate freely

and there is no interference with oar locks, oars during use or motor and/or

steering components.

2. Install the ¼ inch bolts using the nylon washers supplied, one on each side of

the hull to provide a water resistant installation. Depending on your watercraft's

construction you may want to use a quality marine sealant to provide additional

watertight protection from water intrusion. Once all fasteners are in place verify that

all fasteners are secure and tight.

Figure B

ANCHOR ROPE ROUTING AND INSTALLATION:

1. The Attwood Anchor Lift System uses 3/16" diameter anchor rope up to 100 foot

capacity. Insert one end of the rope through the hole from the spool side. Tie a knot

in the end of the rope making sure that it is as tight as possible and trim off excess to

avoid rubbing and interference against the base when the reel is in operation.

2. Add slight tension to the line and slowly wind the rope onto the reel in a clockwise

direction. Having slight tension on the line keeps it from binding or becoming tangled

during the winding process and provides for much easier anchor release.

3. Once you have the anchor line wound on to the rope reel route the rope along the

side of the boat, determine if you will need rope guides or swivel pulleys, note the

placement of the guides, and install them following all of the Warnings and Cautions.

(Attwood recommends the use of swivel pulleys and guides to help route the rope to

properly utilize the Anchor Lift System by keeping the rope clear of obstructions and

to avoid undue chafﬁ ng and wear on the rope and the system. These are not supplied

but can be found at your local marine dealer or online at one of the many marine

retailers.)

4. Finalize the routing of the anchor line through the Anchor Mount / Rope Guide

Assembly, attach your anchor, and take up the slack in the line.

5. Verify the routing of the line making sure there is no chafﬁ ng or interference

between; the line, pulleys, guides and the watercraft.

Figure C

ATTWOOD ANCHOR LIFT SYSTEM OPERATION:

1. To actuate the release of the anchor simply turn the release knob in a CLOCKWISE

direction. The anchor will drop until you turn or release the knob back to original

starting position.

3/4 in. diameter

clearance hole

Leave ample clearance for

unobstructed operation